Siemens RUGGEDCOM RS910W Installation Manual Download Page 22

Page: 22 / 52

Chapter 2

Installing the Device

RUGGEDCOM RS910W

Installation Guide

Connecting the Failsafe Alarm Relay

Figure 4: Antenna Installation

3. Repeat

Step 2

for the second antenna.

4. Adjust the position of each antenna as needed.

Section 2.6

Connecting the Failsafe Alarm Relay

The failsafe relay can be configured to latch based on alarm conditions. The NO (Normally Open) contact is closed

when the unit is powered and there are no active alarms. If the device is not powered or if an active alarm is

configured, the relay opens the NO contact and closes the NC (Normally Closed) contact.

NOTE

Control of the failsafe relay output is configurable through ROS. One common application for this relay

is to signal an alarm if a power failure occurs. For more information, refer to the ROS User Guide for

the RUGGEDCOM RS910W.

To connect the failsafe alarm relay, do the following:
1. Insert the failsafe alarm relay terminal block into the device and tighten the screws.
2. Connect a failsafe device to the terminal block.

Summary of Contents for RUGGEDCOM RS910W





















































Search results

Summary of Contents for RUGGEDCOM RS910W

Reviews:

Related manuals for RUGGEDCOM RS910W

Brands by name

Popular brands

Siemens RUGGEDCOM RS910W, Installation Manual

Search results

Summary of Contents for RUGGEDCOM RS910W

Reviews:

Related manuals for RUGGEDCOM RS910W

Brands by name

Popular brands