manualshive.com logo in svg

Siemens RDY2000, Installation Instructions Manual, Page: 18 / 18

Share
Download
Siemens RDY2000 Installation Instructions Manual Download Page 18

 

Page 18 of 18

 

Siemens Industry, Inc. 

 

Table 15.  Record Field Settings. 

Parameter 

Definition 

Default 

Field Value 

P101 

System Type 

CO 

 

P102 

Cooling Stages 

2 

 

P103 

Heating Stages 

2 

 

P104 

Aux Heating Stages 

0 

 

P105 

Fan Operation 

NO 

 

P106 

Reversing Valve 

O 

 

P107 

Scheduler Days 

2 

 

P108 

Program Periods 

2 

 

P110 

Auto Change 

YES 

 

P111 

Changeover Deadband 

5°F (2.5°C) 

 

P112 

Daylight Savings 

YES 

 

P201 

Heat Temp Limit 

95°F (35.0°C) 

 

P202 

Cool Temp Limit 

50°F (10.0°C) 

 

P203 

Temperature Display Offset 

0°F (0°C) 

 

P204 

Override Time Limit 

--- 

 

P205 

Override Temp Limit 

--- 

 

P206 

Heat Pump Compressor Lock Out 

OFF 

 

P207 

Heat Pump Auxiliary Heat Lockout 

OFF 

 

P208 

Service UV Lamp 

0 

 

P209 

Service Humidifier 

0 

 

P210 

Service Air Filter 

0 

 

P211 

Keypad Lockout 

0 

 

P213 

Backlight 

15 

 

P301 

Configurable Input 1 (IN1) 

0 

 

P302 

Temperature Input 1 Type 

0 

 

P303 

Temperature Input 1 Low 

0°F (-18.0°C) 

 

P304 

Temperature Input 1 High 

120°F (50°C) 

 

P305 

Configurable Input 2 (IN2) 

0 

 

P306 

Temperature Input 2 Type 

0 

 

P307 

Temperature Input 2 Low 

0°F (-18.0°C) 

 

P308 

Temperature Input 2 High 

120°F (50.0°C) 

 

P309 

Configurable Input 3 (IN3) 

0 

 

P310 

Temperature Input 3 Type 

0 

 

P311 

Temperature Input 3 Low 

0°F (-18.0°C) 

 

P312 

Temperature Input 3 High 

120°F (50.0°C) 

 

P313 

Configurable Input 4 (IN4) 

0 

 

P314 

Temperature Input 4 Type 

0 

 

P315 

Temperature Input 4 Low 

0°F (-18.0°C) 

 

P316 

Temperature Input 4 High 

120°F (50.0°C) 

 

P317 

Aux Output 1 (OUT1) 

0 

 

P318 

Aux Output 2 (OUT2) 

0 

 

P319 

Aux Output 3 (OUT3 & C3) 

0 

 

P320 

Independent Humidity Control 

No 

 

P401 

Unit Number 

--- 

 

P402 

CO2 Setpoint 

800 

 

P403 

Pre-Occupancy Purge 

0 

 

P404 

Occupancy Sensor Min Run Timer 

30 

 

P405 

Semi-Continuous Fan 

NO 

 

P407 

Installer Password 

0000 

 

P701 

Firmware Revision 

N/A 

 

P501 

Stage Delay - Cooling 

2 

 

P502 

Stage Differential - Cooling 

1°F (0.5°C) 

 

P503 

Cooling Minimum Off Time 

5 

 

P504 

Cooling Minimum On Time 

3 

 

P505 

Changeover Delay 

10 

 

P506 

Cooling Deadband 

1°F 

 

P507 

Stage Delay - Heating 

2 

 

P508 

Stage Differential - Heating 

Conv. = 1°F (0.5°C); HP = 2°F (1°C) 

 

P509 

Heating Minimum Off Time 

5 

 

P510 

Heating Minimum On Time 

5 (10 if heat pump) 

 

P511 

Heating Deadband 

1°F (0.5°C) 

 

P911 

Expert Password 

99:99 

 

 

Summary of Contents for RDY2000



















Reviews:

No comments