Siemens MD-12HD, User Manual, Page: 56 / 74

55 Siemens Industry, Inc.
3 Wire 3
ɸ
(Delta)
Service Type 2
V_Input 1 or 2
Description 31 Char
Channels Volt Ref CT Type Range Phase Shift CT
Multiplier
CT Sign
CH1 L1
– N
[1] mV [1] or
RōCoil
[2] Any > 0A -3.0
˚ to +3.0˚
Any > 0 [1] 0 or 1
CH2 L2
– N
[2] mV [1] or
RōCoil
[2] Same as 1 Same as 1 Same as 1 0 or 1
CH3 L3
– N
[3] mV [1] or
RōCoil
[2] Same as 1 Same as 1 Same as 1 0 or 1
Even though CH2 is calculated internally, it is recommended that the CT settings reflect those from CH1, rather than being left at
factory default, to facilitate configuration validation from the RTU.
2 Wire 1
ɸ
( Plug
Load)
Service Type 3
V_Input 1 or 2
Description 31 Char
Channels Volt Ref CT Type Range Phase
Shift
CT
Multiplier
CT Sign
CH1 ANY [1-6] mV [1] or
RōCoil
[2] Any > 0A -3.0
˚ to +3.0˚
Any > 0 [1] 0 or 1
CH2 ANY [1-6] mV [1] or
RōCoil
[2] Any > 0A -3.0
˚ to +3.0˚
Any > 0 [1] 0 or 1
CH3 ANY [1-6] mV [1] or
RōCoil
[2] Any > 0A -3.0
˚ to +3.0˚
Any > 0 [1] 0 or 1
Any channel that needs to be turned OFF should set the CT Type to OFF.
3 Wire 1
ɸ
(Split
Phase)
Service Type 4
V_Input 1 or 2
Description 31 Char
Channels Volt Ref CT Type Range Phase
Shift
CT Multiplier CT Sign
CH1 L1
– N
[1] mV [1] or
RōCoil
[2]
Any > 0A -3.0
˚ to +3.0˚
Any > 0 [1] 0 or 1
CH2 L2
– N
[2] mV [1] or
RōCoil
[2] Any > 0A -3.0
˚ to +3.0˚
Any > 0 [1] 0 or 1
CH3 L3
– N
[3] OFF [0] Any > 0A -3.0
˚ to +3.0˚
Any > 0 [1] 0 or 1
Even though CH3 is not used for computation it is recommended that the CT settings reflect those from CH1 rather than being left at
factory default to facilitate configuration validation from the RTU.
Disabled (OFF)
Service Type 5
V_Input 1 or 2
Description 31 Char
Channels Volt Ref CT Type Range Phase
Shift
CT Multiplier CT
Sign
CH1 L1
– N
[1] OFF [0] Any > 0A -3.0
˚ to +3.0˚
Any > 0 [1] 0 or 1
CH2 L2
– N
[2] OFF [0] Any > 0A -3.0
˚ to +3.0˚
Any > 0 [1] 0 or 1
CH3 L3
– N
[3] OFF [0] Any > 0A -3.0
˚ to +3.0˚
Any > 0 [1] 0 or 1
Even though disabled channels are not used in calculations and report 0.0 they still contain configuration information. It is suggested
that they be set to a known value rather than left at defaults to facilitate configuration validation by the RTU.