background image

Installation instructions

 en

13

12.6 Instructions for the electrical
connection

In order to be able to safely connect the appliance to
the electrical system, follow these instructions.

WARNING ‒ Risk of electric shock!

It must always be possible to disconnect the appliance
from the electricity supply. The appliance must only be
connected to a protective contact socket that has been
correctly installed.

The mains plug for the mains power cable must be
easily accessible after the appliance is installed.

If this is not possible, an all-pole isolating switch
must be integrated into the permanent electrical in-
stallation according to the conditions of overvoltage
category III and according to the installation regula-
tions.

The permanent electrical installation must only be
wired by a professional electrician. We recommend
installing a residual-current circuit breaker (RCCB)
in the appliance's power supply circuit.

Sharp-edged components inside the appliance may
damage the connecting cable.

Do not kink or trap the connecting cable.

¡

The connection data can be found on the rating
plate inside the appliance.

¡

To see the rating plate, remove the grease filter.

¡

The connecting cable is approx. 1.30 m long.

¡

This appliance complies with the EC interference
suppression regulations.

¡

The appliance corresponds to protection class 1.
Therefore, only use the appliance with a protective
earth connection.

¡

Do not connect the appliance to the power supply
during installation.

¡

Ensure that the protection against contact is guaran-
teed during installation.

12.7 General information

Follow these general instructions during the installation.

¡

For the installation, observe the currently valid build-
ing regulations and the regulations of the local elec-
tricity and gas suppliers.

¡

When discharging the exhaust air, the official and
legal regulations, such as the regional building
code., must be observed.

¡

The width of the extractor hood must correspond at
least with the width of the hob.

¡

To optimally detect the cooking vapours, install the
appliance in the middle of the hob.

¡

In order to freely access the appliance for servicing,
select an easy-to-reach installation site.

¡

The surfaces of the appliance are sensitive. Avoid
damaging them during installation.

12.8 Installation

Checking the unit

1.

Check whether the fitted unit is level and has suffi-
cient load-bearing capacity.
The max. weight of the appliance is 18 kg.

Note: 

Note the furniture manufacturer's specifica-

tions with regard to the load-bearing capacity of the
fitted unit.

2.

Ensure that the fitted unit is heat-resistant up to
90 °C.

3.

Ensure that the fitted unit is still stable after the cut-
outs have been made.

4.

Ensure that the fitted unit complies with the following
dimensions:

Width

600 mm

Depth

Min. 320 mm
With lowering frame:
Min. 350 mm

Position

Min. 390 mm
With CleanAir circulat-
ing-air set, min. 600 mm

Wall thickness

16 mm or 19 mm

Preparing the units

Requirement:

 The unit is suitable for the installation. 

→ 

"Checking the unit", Page 13

1.

Cover the hob to prevent damage.

2.

Ensure that the stability of the fitted unit is guaran-
teed after the cut-outs have been made.

3.

If the cabinet is less than 320 mm deep, remove
part of the back panel.

4.

Create the cut-out for the pipe connection.

5.

If the cabinet base is in place, remove it.

6.

Remove any shavings.

7.

Use the enclosed mounting part to mark the fasten-
ing points on the inside of the cabinet and use a
bradawl to make indentations where the holes are
to be.

≥170

Summary of Contents for LI67RA531C





















Reviews: