en
Ventilation function Crisp Finish
22
4.
To change the preset cooking time, press the relev-
ant time value, e.g. minute display "min" or second
display "s".
a
The selected value is marked in blue.
5.
Set the cooking time using the adjustment line or
enter it directly via the number field .
If required, use to reset the adjustment value.
6.
Use "Start" to start the operation.
a
The microwave starts and the cooking time counts
down. The display shows the performance reduction
→
"Microwave output settings", Page 12
for the
maximum microwave output. "Boost"
a
Once the cooking time has elapsed, a signal tone
sounds. A notification appears on the display con-
firming that the operation has finished.
7.
Once the cooking time has elapsed:
‒
If required, you can select other settings and re-
start the operation.
‒
When the food is ready, use to switch the ap-
pliance off.
8.
If you have switched off the drying function for the
microwave in the basic settings, dry the cooking
compartment.
→
Note:
If you open the appliance door during operation,
the operation stops. If you close the appliance door,
you must continue the operation. If you have changed
the basic setting for this, make sure that the microwave
does not resume operation without food inside.
→
Changing the microwave output setting
You can change the microwave output at any time.
1.
Press the microwave output setting.
2.
Change the microwave output setting.
3.
Press "Apply".
Changing the cooking time
You can change the cooking time at any time.
1.
Press the cooking time.
2.
Change the cooking time using the adjustment line
or enter it directly via the number field .
3.
Press "Apply".
12.4 Setting added microwave
Note:
Note the correct way to operate the microwave:
¡
¡
"Preventing material damage", Page 7
¡
"Microwave output settings", Page 12
¡
"Cookware and accessories with microwave",
Requirement:
Observe the information about the re-
spective operating mode.
→
"Setting options with the microwave", Page 21
1.
Press the operating mode that you require.
2.
Implement the settings for the operating mode, e.g.
type of heating and temperature.
3.
Press "Added microwave" .
4.
Press the required microwave output setting.
5.
Press "Cooking time" and set the cooking time.
6.
Use "Start" to start the operation.
a
The appliance starts to heat and the time counts
down.
a
Once the cooking time has elapsed, a signal tone
sounds. A notification appears on the display con-
firming that the operation has finished.
7.
Once the cooking time has elapsed:
‒
If required, you can select other settings and re-
start the operation.
‒
When the food is ready, use to switch the ap-
pliance off.
Changing added microwave
You can change or deactivate the added microwave at
any time.
1.
Press the microwave output setting.
2.
Change or deactivate the microwave output setting.
3.
Press "Apply".
13 Ventilation function Crisp Finish
The ventilation function "Crisp Finish" extracts mois-
ture from the cooking compartment so that your meal
will be more crispy.
Hot steam that may escape when the appliance door is
opened is reduced.
13.1 Suitable types of heating with the
ventilation function
Only certain types of heating are suitable for the ventil-
ation function.
You can use the ventilation function for the following
types of heating:
¡
4D hot air
¡
Top/bottom heating
¡
coolStart function
¡
Intensive heat
¡
Pizza setting
¡
Circulated air grilling
13.2 Setting the ventilation function
You can activate the ventilation function at any time,
even after the start of the operation.
1.
Set a suitable type of heating and a temperature.
If required, you can select other settings and com-
bine with the ventilation function.
2.
Press "Crisp Finish".
a
"On" is in the tile.
3.
Press "Start" to start the operation.
a
The appliance starts heating.
a
The setting values are shown on the display.
4.
When the food is ready, use to switch the appli-
ance off.
Note:
Amplified fan noises can be heard while the ap-
pliance is in operation.
Cancelling the ventilation function
You can switch off the ventilation function at any time.
▶
Press "Crisp Finish" .
