Siemens hicom 150 H optiset E standard Page 36 Service Manual Download

Page: 36 / 47

Initial startup of HiPath HG 1500

lan2de.c03

A31003-K5020-S100-6-7620
Service Manual

3-5

For internal use only

Startup

3.2.1 Configuration HiPath HG 1500

3.2.2 Configuring the NGK 100 gatekeeper

Relevant options under "Settings

Step

Task

Under

Voice Clients -> Gatekeeper

Enter the IP address of the PC with the gatekeeper,
enable gatekeeper support and configure the prefix.

Under

Voice Clients -> H.323 Clients

Configure the clients with a gatekeeper connection using IP address
"255.255.255.255".
Clients without a gatekeeper connection must be configured with the fixed
IP addresses of the corresponding PCs.

Under

Voice Clients -> Xpress Clients

There are no additional aspects to be noted here.

Step

Task

Capacity Characteristics:
Set the

IRQ interval

if the registered endpoints do not need to be cy-

clically polled, e.g. when using RAS connections for teleworking.

Call and Registration Policy:

Accept Call

must be enabled.

Set

All Endpoints

Predefined endpoints

Routing Mode:
Set

Gatekeeper Routed

Direct Routed

Summary of Contents for hicom 150 H optiset E standard
















































Search results

Summary of Contents for hicom 150 H optiset E standard

Reviews:

Related manuals for hicom 150 H optiset E standard

Brands by name

Popular brands

Siemens hicom 150 H optiset E standard, Service Manual

Search results

Summary of Contents for hicom 150 H optiset E standard

Reviews:

Related manuals for hicom 150 H optiset E standard

Brands by name

Popular brands