manualshive.com logo in svg

Siemens hicom 150 H optiset E standard, Service Manual, Page: 32 / 47

Share
Download
Siemens hicom 150 H optiset E standard Service Manual Download Page 32

Initial startup of HiPath HG 1500

lan2de.c03

A31003-K5020-S100-6-7620 
Service Manual

3-1

For internal use only

Startup

3 Startup

3.1 Initial startup of HiPath HG 1500

Note

Windows 3.11 is no longer supported.

3.1.1 Initial startup: Remote via modem

Prerequisites

The feature is only available as of Hicom Rel. 3 SMR-E with Assistant Office P30300-
P1584-A1-02 and SMR-11 HG1500. Hicom must be configured for remote adminis-
tration and HiPath HG 1500 must be in the default state (default customer database).

Step

Task

1.

Using Assistant E, read out the contents of the board using the Restart/
Reload option "Maintenance". Then enter an 

existing

 call number as an 

extension in the numbering plan. (Recommendation: Pro -748, Com -686, 
Point -69)

2.

Transfer the changes into Hicom using "Transfer data"

3.

The following changes will automatically be made in the customer data-
base for HiPath HG 1500:
- the ISDN peer "remote default" will be set with the following parameters:
IP address: 10.186.237.64
CHAP user ID: 31994 (Host = On)
CHAP password: 31994
V.34 peer: Yes
- the ISDN2 interface is assigned the IP address 10.186.237.63
- the IP address 10.186.237.64 is assigned administration rights

4.

A new dial-up networking connection with the following data is generated 
on the PC (here W98):
Connect via: Standard 19200 bps modem (dependent on the modem in 
use)
Type of Dial-Up Server> PPP Windows 95, Windows NT 3.5
Logon to the network: No
Activate software compression: No
Request encrypted password: No
NetBEUI: No
IPX/SPX: No
Define IP address: 10.186.237.64
Use IP header compression: No
Use the standard GW in the remote network: No

Summary of Contents for hicom 150 H optiset E standard
















































Reviews:

No comments