Siemens HB34D553 Series, Instruction Manual

Page: 18 / 32

18
Appliance does not start.
Nx ‹
:
…‹
min
appears in the display.
Cleaning aid or descaling was cancelled
Turn the operating mode selector to
È
or
calc
and rinse the appliance twice
(see section "Cancelling the cleaning aid"
or "Cancelling descaling")
The appliance cannot be started The appliance door is not fully closed Close the appliance door.
The appliance is not in operation. A dura-
tion is shown in the display
A control knob was unintentionally
pressed
Press and hold the
†
button
The † button was not pressed after mak-
ing the setting
Press the † button briefly to start the
cooking operation, or press and hold the
†
button to cancel the setting
Appliance does not start. A signal sounds A temperature outside of the possible tem-
perature range has been set
Check the temperature ranges for the
operating modes
Turning the temperature selector cancels
the cooking operation
A temperature outside of the possible tem-
perature range has been set
Check the temperature ranges for the
operating modes. Press the
†
button
0
and
‹
:
‹‹
light up in the display Power cut Reset the clock time (see section: "Time-
setting options")
”‰
is shown in the display
The automatic safety switch-off is active Press any button.
The
¯
indicator appears even though the
water tank is full
The water tank has not been pushed in
properly
Slide in the water tank until it engages
The detection system is not working Call the after-sales service
The ¯ indicator appears even though the
water tank is not yet empty, or the water
tank is empty but the
¯
indicator does not
appear
The water tank is dirty. The mobile water
level indicators are jammed
Shake and clean the water tank. If the
parts cannot be released, obtain a new
water tank from the after-sales service.
The water tank empties for no discernible
reason. The evaporator dish is overflowing
The water tank was not closed properly Close the lid until you feel it engage.
The tank cover seal is dirty Clean the seal
The seal in the tank cover is defective Obtain a new water tank from the after-
sales service
The evaporator dish has boiled dry even
though the water tank is full
The water tank has not been pushed in
properly
Slide in the water tank until it engages
The feed line is blocked Descale the appliance. Check whether the
water hardness is set correctly
The
¯
indicator appears The appliance has not been used for at
least 2 days and the water tank is full
Empty and clean the water tank. Always
empty the water tank after cooking
There is a "pop" noise during cooking Cold/warm effect with frozen food, caused
by the steam
This is normal.
When you cook with steam, a lot of steam
is created
The appliance is being automatically cali-
brated
This is normal.
When cooking with steam, a lot of steam is
created again
The appliance is unable to calibrate itself
automatically if cooking times are too
short
Reset the appliance to the factory settings
(see Basic settings section). Then start
steaming at 100 °C for 20 minutes
Steam escapes from the ventilation slots
during cooking
This is normal.
The appliance is not producing steam
properly
Limescale has formed in the appliance Start descaling (see Section: Descaling)
Error message
“‹‚‚
appears in the dis-
play
A button was pressed for too long or is
jammed
Press the
0
button to clear the fault mes-
sage. Press each button and check that it
is clean
An
“
... error message appears in the dis-
play
Technical fault.
Press the
0
button to delete the error
message. Reset the clock if required. If the
error message appears again, call the
after-sales service
The appliance is not heating. The colon
flashes in the display
A button combination was actuated Set the Steam operating mode to 35 °C,
then press and hold the
@ button until a
signal sounds. Press the
@
button again
briefly
Problem Possible cause Notes/remedy