Siemens Gigaset C450 IP Owner'S Manual Download

Page: 70 / 106

Appendix

Gigaset C450 IP / Greek eng / A31008-M1713-T151-3-8U19 / appendix.fm / 24.9.07

Ver

on 4, 16.

09.20

Questions and answers

If you have any questions about using

your phone, visit us at any time at

www.siemens.com/gigasetcustomercare.

The table below contains a list of common

problems and possible solutions.

Please note:

To support the service team, it can be helpful if

you have the following information to hand:
– Version of firmware, EEPROM and your

phone's MAC address
You can check this information with the

Web configurator (page 67). For how to

check the MAC address displayed on your

handset, turn to page 49.

– VoIP status code (page 71)

For problems with VoIP connections, you

should set VoIP status messages to be dis-

played on your handset. (page 48,

page 66). These messages contain a status

code that helps when the problem is ana-

lysed.

The display is blank.

1. The handset is not switched on.

Press and

hold

the end call key

2. The battery is flat.

Charge the battery or replace it

(page 6).

The handset does not respond to a key

press.

The keypad lock is activated.

Press and

hold

the hash key

(page 21).

Base

flashes in the display.

1. The handset is outside the range of the

base station.

Move the handset closer to the base

station.

2. The base station is not switched on.

Check the base station mains adapter

(page 8).

3. An update of the base station firmware is

currently being conducted (page 46/

page 65).

Please wait until the update is complete.

Please Register

flashes in the display.

The handset is not registered.

Handset does not ring.

The ringer tone is switched off.

Activate the ringer tone (page 43).

You cannot hear a ring/dialling tone from

the fixed network.

Base station's phone cord has been replaced.

When purchasing a new cord, ensure that it

has the correct pin connections (page 9).

When making calls from the fixed network,

the caller's phone number is not displayed

although CLIP (page 19) is set.
Phone number identification is not enabled.

The

caller

should ask his network provider

to enable Calling Line Identification (CLI).

You hear an error tone when keying an

input

(a descending tone sequence).

Action has failed/invalid input.

Repeat the operation.
Watch the display and refer to the user

guide if necessary.

You cannot connect to the router and the

phone is assigned a static IP address.

Check on the router whether the IP address

is already being used by another device in

the LAN or belongs to the block of IP

addresses that is reserved on the router for

dynamic address assignment.

If necessary, change the phone's IP address

(page 49).

You have made a call via VoIP but cannot

hear the other participant

Your phone is connected to a router with NAT/

firewall.

Your STUN server or outbound proxy set-

tings are incomplete or incorrect. Check the

settings (page 60, page 60).

No outbound proxy is entered or the out-

bound proxy mode

Never

is activated

(page 60) and your phone is connected to a

router with symmetric NAT or a blocking

firewall.

Port forwarding is activated on your router,

but no permanent IP address has been

assigned to your phone.

Summary of Contents for Gigaset C450 IP











































































































Search results

Summary of Contents for Gigaset C450 IP

Reviews:

Related manuals for Gigaset C450 IP

Brands by name

Popular brands

Siemens Gigaset C450 IP, Owner'S Manual

Search results

Summary of Contents for Gigaset C450 IP

Reviews:

Related manuals for Gigaset C450 IP

Brands by name

Popular brands