background image

4

Siemens Industry, Inc.
Building Technologies Division

A6V10324662_g_en_US

 

201

6

-0

1

-

20

MOUNTING

Input/output module FDCIO422 can be mounted
directly into a 4

11

/

16

-inch square box or 5-inch

square box.
An additional extension ring can be mounted on
the 4

11

/

16

-inch square box with two screws.

For mounting the input/output module in the
5-inch square box use a 4

11

/

16

-inch adapter

plate.

Fasten the module to the square box with the
4 screws provided with the box.
Fasten the faceplate on the carrier using the
2 screws provided with the FDCIO422.

Be sure to program the FDCIO422 before
fastening the faceplate to the unit.

Volume allowance FDCIO422

FDCIO422 Volume 11.7 inch

3

,

max. 20 conductors
Check NFPA70, National Electric Code
‘314.16 Number of Conductors in Outlet,
Device and Junction Boxes, and Conduit’,
Table 314.16(A) and (B), to choose the
correct metal box (4

11

/

16

-inch square box,

4

11

/

16

-inch square box with extension ring

or 5-inch square box).

WARNING

It is not allowed to use the module without
the faceplate. Remove the faceplate for
service and maintenance reasons only!

Figure 7 Mounting the FDCIO422

TECHNICAL DATA

Operating voltage:

DC 12 – 32 V

Operating current
(quiescent):

1 mA

Absolute maximum
peak current:

1.92 mA

Maximum current
connection factor

2)

:

4

Relays output

1)

:

(normally open /
normally closed)

DC 30 V / AC 125 V
Max. 4x 5 A or
2x 7 A (OUT B, C) or
1x 8 A (OUT C)

Operating
temperature:

32 – 120 °F / 0 – 49 °C

Storage temperature:  -22 – +140 °F / -30 – +60 °C
Humidity:

5 – 85 % R.H. (not freezing
and condensing at low
temperature)

Communication
protocol:

FDnet (supervised Signaling
line circuit, Power limited)

Color:

Carrier: ~RAL 9017
Cage cover: transparent
Cage: ~RAL 9017
Faceplate: white

Standards:

UL 864, ULC-S 527, FM 3010,

 

UL 2572

Approvals:

UL / ULC / FM

System compatibility  FC2005, FC2025, FC2050,

FV2025, FV2050, FC901,
FC922, FC924, FV922,
FV924 & FireFinder XLS

Dimensions:

4.1 x 4.7 x 1.2 inch

Volume (cage and
carrier):

11.7 inch

3

1)

2 coil latching type, dry contact, Form A

2)

Average charge current of the device. 1 Load Unit (LU)
equals to 250 µA

11

16

1

8

11

16

ADAPTER PLATE

11

16

4     INCH EXTENSION RING

INCHES DEEP (29.5 in³)

FDCIO422

CONTROL MODULE BARRIER

(SUPPLIED)

FACEPLATE
5

INCHES

(SUPPLIED)

½

Summary of Contents for FDCIO422









Reviews: