Cleaning function
en
33
Cancelling the cleaning operation
Use the "On/off" button to switch off the oven. The
cooking compartment door cannot be opened until the
H
symbol goes out in the status bar.
Adjusting the cleaning setting
Once cleaning starts, the cleaning setting can no longer
be changed.
You can set the cleaning to run overnight
In the section "Time settings", you can find out how to
delay the end time. This allows you to use the oven at
any time throughout the day.
Once the cleaning function has ended
Once the cooking compartment has cooled down, use
a damp cloth to wipe off the ash that has been left
behind in the cooking compartment, on the shelves and
around the appliance door.
Wipe the pull-out rails with a damp cloth. Then slide the
pull-out rails in and out several times. After cleaning,
some discolouration may remain on the pull-out rails.
This has no effect on performance.
Notes
■
During cleaning, the frame on the inside of the
appliance door may discolour. This is normal and
does not affect performance. The discolouration can
only be removed using a stainless-steel cleaning
agent.
■
Very bad soiling may cause white deposits to remain
on the enamel surfaces. This is residue from the
food and is harmless. It does not affect performance.
You can remove these residues using lemon juice if
required.
Descaling
To ensure that your appliance continues to operate
correctly, it must be descaled regularly.
Descaling comprises a number of different steps. For
hygiene reasons, the descaling programme must be
run through completely before the appliance is ready
for operation again. In total, the descaling programme
runs for approx. 70–95
minutes.
■
Descale (approx. 55–70 minutes), then empty and
refill the water tank
■
First rinsing cycle (approx. 9–12 minutes), then
empty and refill the water tank
■
Second rinsing cycle (approx. 9–12 minutes), then
empty and dry the water tank
If descaling is interrupted (e.g. due to a power failure or
because the appliance is switched off), you will be
prompted to rinse the appliance twice when you switch
it back on. The appliance cannot be used until the
second rinsing cycle has finished.
The frequency with which the appliance must be
descaled depends on the hardness of the water used.
When only another five or fewer steam-assisted
operations are possible, the appliance reminds you to
descale it with a message on the display. The number
of remaining operations is displayed after the appliance
is switched on. You can therefore prepare for the
descaling in good time.
Starting
Caution!
■
Risk of damage to the appliance: Only use liquid
descalers recommended by us for the descaling
programme. The time the product needs to work
during descaling depends on the type of descaler
used. Other descalers may damage the appliance.
Descaler order no. 311
680
■
Descaling solution: Do not allow any descaling
solution or descaler to come into contact with the
control panel or other surfaces on the appliance.
This damages the surfaces. If this does happen,
remove the descaling solution immediately with
water.
If you have used a steam-assisted operation
immediately before descaling, you must first switch the
appliance off so that the residual water is pumped out
of the evaporator system.
1.
Mix 400
ml water with 200
ml liquid descaler to
make a descaling solution.
2.
Press the On/Off button.
3.
Remove the water tank and fill it with descaling
solution.
4.
Once the water tank has been filled with descaling
solution, push it back in again fully.
5.
Close the control panel.
6.
Press the Menu button.
The operating modes menu opens.
7.
Select the "Descaling" operating mode.
If you touch the "Next" field, information on the
cleaning operation is displayed.
The duration of the descaling programme is
displayed. It cannot be changed.
8.
Press the "Start/stop" button to start the cleaning
operation.
The appliance is descaled. You can see the duration
counting down in the status bar. An audible signal
sounds once descaling has finished.
First rinsing cycle
1.
Open the control panel.
2.
Remove the water tank, rinse thoroughly, fill with
water and reinsert.
3.
Close the control panel.
4.
Press the Start/Stop button to start.
The appliance rinses. As soon as the rinsing cycle
has run through, a signal sounds.
Second rinsing cycle
1.
Open the control panel.
2.
Remove the water tank, rinse thoroughly, fill with
water and reinsert.
3.
Close the control panel.
4.
Press the Start/Stop button to start.
The appliance rinses. As soon as the rinsing cycle
has run through, a signal sounds.
Subsequent cleaning
1.
Open the control panel.
2.
Empty and dry the water tank.
3.
Switch off the appliance.
Descaling is complete and the appliance is ready for
use again.
