Siemens CCWC1345-LX Configuration Manual Download Page 2

Liefermöglichkeiten und technische Änderungen vorbehalten. 
Data and design subject to change without notice. / Supply subject to availability. 
© 2006 Copyright by 
Siemens Building Technologies AG 
 
Wir behalten uns alle Rechte an diesem Dokument und an dem in ihm dargestellten Gegenstand vor. Der Empfänger erkennt diese Rechte 
an und wird dieses Dokument nicht ohne unsere vorgängige schriftliche Ermächtigung ganz oder teilweise Dritten zugänglich machen oder 
außerhalb des Zweckes verwenden, zu dem es ihm übergeben worden ist. 
 
We reserve all rights in this document and in the subject thereof. By acceptance of the document the recipient acknowledges these rights 
and undertakes not to publish the document nor the subject thereof in full or in part, nor to make them available to any third party without our 
prior express written authorization, nor to use it for any purpose other than for which it was delivered to him. 
 

Dear Customer 

By selecting this SIEMENS product, you have chosen a professional device that 
guarantees the highest possible quality and reliability. We would like to thank you 
very much for your confidence in our products and kindly ask you to read the 
following instructions carefully before installing and using the product, in order to 
take full advantage of all quality features included in this product line. 

WARNING 

To reduce the risk of fire or electrical shock, do not expose this product to rain or 
moisture. It should be installed by a qualified service person and should conform to 
all local codes.  Please connect the equipment to a 12 V DC or 24 V AC Class 2 
power supply if the LP camera model is to be installed. 

Summary of Contents for CCWC1345-LX



































Reviews: