Siemens 8BK30, Operation And Maintenance Instructions

Page: 26 / 28

27 26
4.1.4
ාࣂ
ൣল߾ፕ঳ຐᅜࢫ
•
ሞਸ࠲ࡋत๮כևݴLjාࣂ߳থںਸ࠲ڦةཀྵLjዡ׶ᅜत
থںਸ࠲ቄோᇑ๮כևݴऐႁۯፕᆶ࠲ڦঔ૾ă
•
ාࣂோঔ૾ࢅ໮ă
4.2
Ⴊ૙
4.2.1
ሞ৆थ൧઄ူසࢆٶਸோ૴໮
ߛუ๪ڦோ૴໮ሞ๮כևݴ݀ิࠤቱࢫLjփీॽ๮כཽ዁܏
ਸ࿋ዃ৊ႜႪ૙߾ፕ้Ljኻᆶᆩُ݆֍੗ᅜٶਸă
Ӏቷ
DIN VDE 0105
ࡀۨॽਸ࠲ࡋ߰૗ࢅথںă
֡ፕසူǖ
•
ॽோ໮ኍႂူDŽ
8
Lj཮
17
Dž LjྺُLjٗ
14
ਸ੨تDŽ཮
14
Dž
֭෇அີژLjႂူ໮ኍă
•
ॽሃ׽֭෇੥
10
ժݒ้ኍ჉ገ
90°
ă
•
ॽோ๮դDŽ
11
Lj཮
14
Dž༵ഐ዁ፌߛ࿋ዃLjժٶਸோă
Ⴊ૙߾ፕ঳ຐᅜࢫLjॽோ໮ኍ
(8
Lj཮
17)
჉෇ோ໮੥ా
(9
Lj཮
17)
Ljۙኝ዁
32mm(
཮
18)
ă
4.2.2
ऐႁᆌथĐݴቄđ֡ፕ
ᆩ
T
႙๮դᅎۯ๮כ
•
ၠᆸઙ
T
႙๮դ֭੥߃ӱڦդDŽ
8
Lj཮
14
Dž Ljժ֭෇
T
႙๮
դDŽ
7
Lj཮
14
Dž዁֭੥ాă
•
ॽ
T
႙๮դݒ้ኍገۯ
90°
LjٗĐ໮ۨ
”
࿋ዃ዁Đ঴໮đ
࿋ዃDŽ཮
15
ዐᄕ࿋ዃDž ă
4.2.3
ଭևॲڦ߸࣑
ਨᇹጱLj༫࠶LjةཀྵLjᅏ՗Ljۉୁࢻߌഗڪ਩੗ᅜᆩႎڦ߸࣑ă
ස߸࣑߾ፕᆶઓవLj੗ᄲ൱ฉ࡛ဇோጱਸ࠲ᆶ၌ࠅິሞ๢ړ
้क़ኸಋටᇵ޶ሴኄၜ߾ፕă
4.1.4 Lubrication
Immediately after cleaning
• grease the isolating contacts in the panel and on the
withdrawable units, the contacts of the earthing switches
as well as the bearings and articulated joints on the
operating mechanisms for the earthing switches, on the
shutters and on the withdrawable units.
• grease the door hinged and locks.
4.2 Repair work
4.2.1 Outwitting the door interlock in emergencies
The door interlock of the HV compartment should only be
outwitted if the withdrawable unit cannot be drawn out into
the disconnected position after a fault has occurred and if
repair work is not possible otherwise.
Isolate and earth the switchboard in accordance with DIN
VDE 0105.
Proceed as follows:
• Unscrew the door locking pin (8,Fig.17). For this purpuse
insert a screwdriver into opening 14 (Fig.14) and unscrew
the pin.
• Insert the double-bit key into lock 10 and turn
anticlockwise by 90 o .
• Lift the door catch (11,Fig.14) to the stop and open the door.
On completion of repair work screw the door locking pin (8,
Flg.17) into the door locking strip (9,Fig.17). Adjust to 32mm
(Fig.18)
4.2.2 Mechanically emergency Off operation
by means of hand crank for moving the withdrawable unit:
• Shift the unlocking knob (8,Fig.14) to the right and insert
the hand crank (7,Fig.14) into the opening.
• Turn the crank anti-clockwise by 90° from the “locked”
position into the “free” position (Fig.15 center).
4.2.3 Replacement of parts
Items such as post insulators, bushings, contacts, measuring
instruments, current tranfermers, etc. can be replaced by
new ones.
If replacement is likely to prove difficult, ask Siemens
Switchgear Ltd., Shanghai in good time for a fitter to be
assigned.
4.1
ྼࢺ
4.1.1
•
ྼࢺྜׯࢫႴፕྜኝڦु୤ă
•
໯ᆶڦྼࢺ߾ፕՂႷᆯᆶጨ߭ڦටᇵઠ֡ፕă
•
֑ᆩᇱጎଭॲ߸࣑ă
•
࠲ᇀْܾᇮॲڦྼࢺLj֖९၎ᆌࠃᆌฆ༵ࠃڦ๮֩ă
• 1000
ْ֡ፕْຕࢫLjՂႷܔথںਸ࠲৊ႜྜኝڦॠֱă
• 1000
ْ֡ፕْຕࢫLjՂႷܔڹಎכ৊ႜྜኝڦॠֱă
4.1.2
ॠֱऺࣄ
௅౎
•
ᅃӯణ֪ॠֱă
•
ॠֱ޹ॲڦྜኝ࿮ඍतኟ׉ጒༀă
௅࿵౎
සࡕՂႷሞజ၍๪֡ፕLjᆌኸಋᅃ࿋Ҿඇᇵᅜݞኹဃࢇਸ
࠲Ǘॠֱ໲ڦ߰૗ጒༀLjথںत܌ୟDŽ
DIN VDE 0105
Džઍ
၍ಇतజಇڦ൧઄ă
•
ॽ๮כཽ዁܏ਸ࿋ዃă
•
ॽኈ੣থةഗतথںਸ࠲ፕᅃْ֡ፕ๬ᄓă
•
؏؜๮כDŽ֖ቷ
3.4.1.2
Džժ৊ႜ໯ᆶࡀۨڦྼႪԍᄢ߾
ፕăܔాևᇮॲLjසۉୁࢻߌഗLjीۉഗLjᅏ՗Ljԍࢺ
ጎዃڪ৊ႜྼႪԍᄢ߾ፕă
•
ൣ෢Ă։৫ਸ࠲ࡋժॠֱথ၍ă
ॠֱஅພ૶থ൧઄ă
•
ාࣂةཀྵLjࣂۯথة௬Ljዡ׶तঔ૾૶থă
•
ዘႎॽ๮כླྀ෇ࡋాă
•
ॠֱਸ࠲ࡋڦ߳ࠀీժ࣬ްਸ࠲ࡋڦ߾ፕă
ኻሞྼႪԍᄢ้ႴᄲՔጚ߾ਏLjྼႪԍᄢ߾ፕྜׯᅜࢫ
Ӏ
2.5
ব৊ႜ֡ፕLjᅜ࣬ްࠀీă
සࡕࣨפডܠLjժ൐੣ഘዐโ܈ᄺডٷ൐๴ڟ࿫කLjྼ
Ⴊԍᄢڦक़߰ᄲ܌ᅃၵă
ඪࢆࠤቱई܌ୟڦᇱᅺۼՂႷகฉֱ௽Ljփ࠶๟ޏᅙঢ়
ࡗ๚ࠤॠֱLj໯ᆶ໦࣋ଭॲۼՂႷ߸࣑ă
4.1.3
ൣল߾ፕ
ൣলवǖෙ୰ᅚྛLjຘጱLjൣলᆩ߅քLjဌפഗă
ෙ୰ᅚဗࢅ຺୰ᅚဗܔਨᇹ֌ଙਏᆶޫ์ႠLjփڥᇀኮথةă
ਨᇹ֌ଙՂႷᆩ೵ཚॆᆩڦൣলवᇑ຤ڦंࢇᅂ৊ႜൣဢă
4.1 Maintenance
4.1.1
• A completed record must be made after maintenance.
• All maintenance work must be carried out by qualified
person.
• Original parts for exchange.
• For secondary component, refer to related manual by
sub-supplier.
• For ES,it is necessary to check completely after 1,000
operating cycles.
• For cassette, it is necessary to check completely after
operating cycles.
4.1.2 Inspection schedule
every year
• general visual inspection.
• check accessories for completeness and proper condition.
every five years
provide a safeguard to prevent unintentional reclosing of
the switchpanels, check its isolated state, earth and
short-circuit (DIN VDE 0105) the feeders and busvars if
work has to be carried out in the busbar compartment.
• Move the withdrawable unit into the disconnected
position.
• Perform a trial operation of the vacuum contactors and
of the earthing switches.
• Withdraw the units (refer to 3.4.1.2) and perform all the
maintenance work specified. Carry out the maintenance
and servicing work for built in equipment such as current
transformers, relays, meters, protective equipment, etc.
• Clean the switchpanela and check the connections.
Check the correct execution of the bolted connections.
• Reinsert the withdrawable units.
• Check the switchpanel functions and resume operation
of the board.
Standard tools only are required for the maintenance work.
Resuming operation after maintenance is described under 2.5.
The maintenance and servicing work is required at shorter
intervals if there is much dust and if the air is very moist and
polluted.
The cause of any disturbance or short-circuit must be
determined immediately and damaged parts replaced,
irrespective of whether an inspection is due or not.
4.1.3 Cleaning
Cleaning agents: Trichlorethane, brushes, cleaning rags,
vacuum cleaner.
Trichlorethylene and tetrachlorethylene have a corroding
effect on parts of isolating material and must not come into
contact with them.
Parts of isolating material should be cleaned with water to
which a common household cleaning agent has been
admixed.
4
NJྼࢺ ᄻْ
4.1
ྼࢺ
................................................................ 26
4.1.1
ྼࢺཉ੼
......................................................... 26
4.1.2
ॠֱऺࣄ
......................................................... 26
4.1.3
ൣল߾ፕ
......................................................... 26
4.1.4
ාࣂ
................................................................ 27
4.2
Ⴊ૙
................................................................ 27
4.2.1
ሞ৆थ൧઄ူසࢆٶਸோ૴໮
.......................... 27
4.2.2
ऐႁᆌथĐݴቄđ֡ፕ
.................................... 27
4.2.3
ଭևॲڦ߸࣑
.................................................. 27
4
NJ
Maintenance Selte
4.1 Maintenance .....................................................26
4.1.1 Maintenance Item ..............................................26
4.1.2 Inspection schedule............................................26
4.1.3 Cleaning ............................................................26
4.1.4 Lubrication.........................................................27
4.2 Repair work
.......................................................27
4.2.1 Outwitting the door interlock in emergencies .....27
4.2.2 Mechanically emergency Off operation...............27
4.2.3 Replacement of parts .........................................27
཮
18
ோ໮ኍ
Fig.18 Door locking pin
ྼ ࢺ
Maintenance