manualshive.com logo in svg

Siemens 6ES7 410-5FM08-0AB0, Equipment Manual, Page: 3 / 34

Share
Download
Siemens 6ES7 410-5FM08-0AB0 Equipment Manual Download Page 3

Table of contents

1

Security information......................................................................................................................................5

2

Introduction...................................................................................................................................................7

3

Safety notes..................................................................................................................................................9

4

Description of the device ............................................................................................................................11
4.1

Components of the product....................................................................................................11

4.2

Synchronization modules for S7–400H ..................................................................................11

5

Assembling .................................................................................................................................................15
5.1

Safety notices for installation .................................................................................................15

5.2

Selecting fiber-optic cables ....................................................................................................16

5.3

Notes on the installation of synchronization modules ............................................................21

5.4

Wiring and inserting the synchronization module...................................................................21

5.5

Removing the synchronization module ..................................................................................22

5.6

Installation of fiber-optic cables..............................................................................................22

6

Connecting up ............................................................................................................................................25
6.1

Safety when connecting up ....................................................................................................25

7

Technical data ............................................................................................................................................27

8

Approvals....................................................................................................................................................29

Tables

Table 5-1

Accessory fiber-optic cable .........................................................................................................16

Table 5-2

Specification of fiber-optic cables for indoor applications............................................................17

Table 5-3

Specification of fiber-optic cables for outdoor applications .........................................................19

Figures

Figure 4-1

Synchronization modules 6ES7960-1AA08-0XA0 and 6ES7960-1Ax06-0XA0 ..........................12

Figure 5-1

Fiber-optic cables, installation using distribution boxes ..............................................................20

Synchronization modules for S7-400H

Equipment Manual, 04/2020, A5E50072434-AA

3

Summary of Contents for 6ES7 410-5FM08-0AB0



































Reviews:

No comments