Siemens 6ES7 410-5FM08-0AB0 Equipment Manual Download Page 12 | Manualshive

Page: 12 / 34

Siemens 6ES7 410-5FM08-0AB0 Equipment Manual Download Page 12

If you remove a synchronization module in redundant system mode, there is a loss of

synchronization. The reserve CPU changes to ERROR-SEARCH mode for some minutes. If

the new synchronization module is inserted and the redundant link is reestablished during this

time, the reserve CPU switches to redundant system mode, otherwise it switches to STOP.
Once you have inserted the new synchronization module and reestablished the redundant link,

you must restart the reserve CPU.

Mechanical configuration

Figure 4-1

Synchronization modules 6ES7960-1AA08-0XA0 and 6ES7960-1Ax06-0XA0

CAUTION

Class 1 laser product
Risk of injury.
The synchronization module is equipped with a laser system and is classified as a "CLASS 1

LASER PRODUCT" according to IEC 60825–1.
Avoid direct contact with the laser beam. Do not open the housing. Always observe the

information provided in this manual, and keep the manual to hand as a reference.

CLASS 1 LASER PRODUCT

LASER KLASSE 1 PRODUKT

TO EN 60825

Description of the device
4.2 Synchronization modules for S7–400H

Synchronization modules for S7-400H

12

Equipment Manual, 04/2020, A5E50072434-AA

«
...
10
11
12
13
14
...
»

Summary of Contents for 6ES7 410-5FM08-0AB0



































Reviews:

No comments