Siemens 1FL3041-0AC31-0BJ0 Functional Description Download Page 20

Page: 20 / 60

3 FM-STEPDRIVE specifications

02.05

3-6

FM-STEPDRIVE/SIMOSTEP (FB)

3.4 Applicable standards, regulations, laws

The following standards, regulations and laws must be observed
when operating the FM-STEPDRIVE:

•

DIN EN 60204 Part 1 (VDE 0113) Electrical equipment of machines

•

DIN VDE 0100

Erection of power installations with

nominal voltages up to 1000 V

•

DIN VDE 0106

Protection against electric shock

•

DIN VDE 0470 (and: IEC 529)

IP degrees of protection

•

DIN VDE 0875 (EN 55011)

Radio interference suppression of

electrical appliances and systems

•

DIN EN 954-1

Safety of machines

Safety-related parts of

control

systems

General design guidelines

If you intend to use the FM-STEPDRIVE power drive in a residential area,
the limit values of the following standards must also be observed:

•

EN 60555

Disturbances in electricity supply

networks caused by household

appliances and similar equipment

•

EN 55022, Class B

Limit values and measurement

methods for information technology

equipment

•

DIN EN 61000 Part 3-2

Electromagnetic compatibility

In case of high interference levels, additional measures must be taken.
We recommend to provide for EMC design of cabinets, e.g. 8MC
cabinets,
(-> catalog NV 21).

The following standards, regulations and laws have been observed
when developing the FM-STEPDRIVE:

•

UL 508

Industrial control equipment

•

CSA C22.2 No 142

Process control equipment

Summary of Contents for 1FL3041-0AC31-0BJ0

















































Search results

Summary of Contents for 1FL3041-0AC31-0BJ0

Reviews:

Related manuals for 1FL3041-0AC31-0BJ0

Brands by name

Popular brands

Siemens 1FL3041-0AC31-0BJ0, Functional Description

Search results

Summary of Contents for 1FL3041-0AC31-0BJ0

Reviews:

Related manuals for 1FL3041-0AC31-0BJ0

Brands by name

Popular brands