background image

 

Settings and add-on modules

ISA Linear Frame Buffer

This field enables you to make available a linear frame buffer for an external
ISA graphics controller. Performance is enhanced if the external ISA
graphics controller can use a linear frame buffer.

Possible entries: 

1MB

2MB

4MB

 or 

Disabled

Default entry: 

Disabled

Set Linear Frame Buffer to

This field shows the address of the linear frame buffer if the field 

ISA Linear

Frame Buffer

 contains a value.

If the field 

ISA Linear Frame Buffer

 contains the entry 

Disabled

, this field

contains 

N/A

 (not applicable).

Disable Shadow Memory Size

If your PC contains an ISA expansion board, it may be necessary that a
memory area is not copied to shadow RAM. The size and location of this
memory area depends on the ISA expansion board.

This field enables you to specify the size of the memory area (max. 64
Kbytes) not to be copied into fast shadow RAM. The area must lie within the
addresses C0000H and DFFFFH.

Possible entries:

Disabled

The entire memory area (C0000H to DFFFFH) is copied into fast shadow
RAM.

16KB, 32KB, 48KB 

or

 64KB

This entry specifies the size of the memory area that is not to be copied
into fast shadow RAM.
You must specify the location of the memory area (base address) in the
field 

Disable Shadow Memory Base

.

Default entry: 

Disabled

A26361-D818-Z120-1-7619

 

15

Settings and add-on modules 

Disable Shadow Memory Base

This field is not applicable if the field 

Disable Shadow Memory Size

 contains the

entry Disabled.

This field enables you to specify the base address of the memory area that is
not to be copied into fast shadow RAM.

Possible entries:

 C0000H

C4000H

C8000H

CC000H

D0000H

D4000H

,

 D8000H

 or 

DC000H

Default entry:  

C0000H

Base Memory Size

This field enables you to set the size of the base memory (below 1 Mbyte).

Possible entries: 

640 KB

 or 

512 KB

Default entry: 

640 KB

IDE DMA Transfer Mode

This entry enables you to set the IDE-DMA transfer mode for your IDE hard
disk drive.
The IDE-DMA transfer mode actually used depends on the installed IDE hard
disk drive.

Possible entries:

Standard

Compatible with DMA transfer mode.

Type B

ISA-DMA transfer mode.

Type F

The fastest IDE-DMA transfer mode. The optimum values are used for the
installed IDE hard disk drive.

Disabled

The function is disabled.

Default entry:

  Type F

16

 

A26361-D818-Z120-1-7619

Summary of Contents for D818



























Reviews: