background image

5

Mounting

5.1

Safety

DANGER

Hazard due to unexpected starting of the machine
Hazard due to electrical voltage

b

Make sure that the outputs of the safety relay have no effect on the machine dur‐
ing mounting and electrical installation.

b

Make sure that the safety relay and the connected components are isolated from
all voltage sources during mounting and electrical installation of the device and
during mounting/dismantling of the front connector.

NOTICE

Enclosure rating IP20 only applies if the front connector is mounted.

5.2

Mounting procedure

Prerequisites

Mounting is done in accordance with EN 50274 and electrical installation in
accordance with IEC 60204-1 in the control cabinet with enclosure rating IP54.

Mounting is done on a 35 mm mounting rail (IEC 60715).

The mounting rail is connected to the functional earth.

The safety relay is installed in a vertical orientation (on a horizontal mounting rail).

There is at least 50 mm of space for air circulation above and below the safety
relay.

There is at least 25 mm of space in front of the safety relay (front side). More
space may be needed depending on the connections.

Approach

Click

Figure 6: Mounting

b

Attach safety relay to mounting rail.

MOUNTING 

5

8020868/ZX84/2018-11-15 | SICK

O P E R A T I N G   I N S T R U C T I O N S | ReLy EMSS1

17

Subject to change without notice

Summary of Contents for 1085345





































Reviews: