SI Zen 2 Pocket Installation Instructions Manual Download Page 12 | Manualshive

Page: 12 / 24

background image

9

Position the fixed track 1” below the brackets and in line with the fabric. Outside of the track
should be flush with pocket jam.

Note: Make sure that the tracks are mounted square to the bracket and plumb from all directions.

INSTALLATION – ZIPPER TRACKS

2

«
...
10
11
12
13
14
...
»

Summary of Contents for Zen 2 Pocket

























Reviews:

No comments

Related manuals for Zen 2 Pocket

Brand: Wayne-Dalton Pages: 20

Brand: Wayne-Dalton Pages: 4

Brand: Wayne-Dalton Pages: 22

Brand: 4Ddoors Pages: 3

Brand: 4Ddoors Pages: 36

Brand: Wallace Perimeter Security Pages: 182

ThermoMark 5150

Brand: Wayne-Dalton Pages: 4

1280LMC-R 1/2 HP

Brand: Chamberlain Pages: 72

Brand: SkyLink Pages: 2

Brand: C.C.E. Pages: 2

Brand: SEA USA Pages: 64

SeceuroGlide Classic

Brand: SWS Pages: 12

Brand: Proteco Pages: 10

Brand: Becker Pages: 20

76380 - Classic Chrome Heavyweight Can...

Brand: Hamilton Beach Pages: 5

Brand: CAME Pages: 16

Brand: CAME Pages: 40

Brand: TOPP Pages: 60

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands