Shuttle Spacewalker AB40 User Manual Download Page 4

Page: 4 / 84

- 2 -

STEP 13 Install Drivers & Software Components .................................... 25

3.2 JUMPER SETTINGS .................................................................................. 26

JUMPERS & CONNECTORS GUIDE .................................................... 27

Jumpers

Clear CMOS Setting (JP1) .................................................................... 30

On board RAID Enable/Disable Setting (JP18) (AB40R only) ................. 31

Back-Panel Connectors

PS/2 Keyboard & PS/2 Mouse Connectors ............................................ 32

USB1/USB2 Port Connectors .................................................................32

COM1/2 Port Connectors ....................................................................... 32

Parallel Port Connector...........................................................................32

Line-Out (Front-Out) Port Connector .......................................................33

Line-In (Rear-Out) Port Connector ........................................................... 33

Mic-In Port Connector ............................................................................. 33

MIDI/GAME Port Connector .................................................................... 33

Front-Panel Connectors

ATX Power On/Off Switch Connector (PWON) ........................................ 34

System Management Interface Connector (EPMI) ...................................34

Green LED/Power LED Connector (GLED/PLED) ................................. 35

HDD LED Connector (HLED) .................................................................35

Power LED Connector (PLED) ............................................................... 36

Hardware Reset Connector (RST) .......................................................... 36

Keylock Connector (KEYLOCK) ............................................................. 36

Speaker Connector (SPEAKER) ............................................................ 37

Extended USB Header (JP4).................................................................. 37

Summary of Contents for Spacewalker AB40





















































































Search results

Summary of Contents for Spacewalker AB40

Reviews:

Related manuals for Spacewalker AB40

Brands by name

Popular brands

Shuttle Spacewalker AB40, User Manual

Search results

Summary of Contents for Spacewalker AB40

Reviews:

Related manuals for Spacewalker AB40

Brands by name

Popular brands