Shuttle AB52P User Manual Download Page 68 | Manualshive

Page: 68 / 76

background image

- 65 -

*** Reload Global Timer Events ***

If any of these items is set to Disabled, system will not monitor the
activity event and reload global timer.
If these items is set to Enabled, system will monitor the system activity
event; if any of the events it monitored, it will cause system to reload
global timer.
These items include Primary IDE0/1, Secondary IDE 0/1, FDD Port,
COM Port, LPT Port,and PCI PIRQ[A-D]#.

Ø

The choice: Disabled or Enabled.

PWRON After PWR-Fail

This item defines if the system will reboot after power fail.

Ø

The choice: On, Off, or Former-sts.

«
...
66
67
68
69
70
...
»

Summary of Contents for AB52P













































































Reviews:

No comments

Related manuals for AB52P

Brand: Abit Pages: 120

Brand: JETWAY Pages: 46

Brand: Quick Pages: 24

Brand: Wintech Pages: 5

Brand: Intel Pages: 97

RTKA788152DE0000BU

Brand: Renesas Pages: 11

Brand: ECS Pages: 46

SPC572LADPT100S

Brand: ST Pages: 29

Brand: MSI Pages: 91

Brand: JETWAY Pages: 44

Brand: EVGA Pages: 14

Brand: Texas Instruments Pages: 6

Brand: Gigabyte Pages: 36

Brand: IBASE Technology Pages: 81

ISL9122AIIN-EVZ

Brand: Renesas Pages: 17

Brand: Silicon Laboratories Pages: 9

Brand: EVGA Pages: 128

OPTIREG PMIC TLF30682QVS01

Brand: Infineon Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands