Shuttle AB52P User Manual Download Page 35 | Manualshive

Page: 35 / 76

background image

- 32 -

Green LED Connector (Green_LED)

The Green-LED(Green_LED) indicates that the system is currently in one of the
power saving mode(Doze/Standby/Suspend). When the system resumes to nor-
mal operation mode, the Green LED will go off. Attach a 2-pin Green LED cable
to Green LED header.

ATX Power On/Off Switch Connector (PW_BTN)

The Power On/Off Switch is a momentary type switch used for turning on or off
the system ATX power supply. Attach the connector cable from the Power Switch
to the 2-pin (PW_BTN) header on the mainboard.

C4

C3

1

HD_LED

RST

NC

PW BTN

Green LED

RSVD

PANEL 1

2

1

HD_LED

RST

NC

PW BTN

Green LED

RSVD

PANEL 1

2

«
...
33
34
35
36
37
...
»

Summary of Contents for AB52P













































































Reviews:

No comments

Related manuals for AB52P

Brand: PC Partner Pages: 20

Brand: Aaeon Pages: 65

Brand: Embest Pages: 91

Brand: ST Pages: 11

Brand: Zotac Pages: 54

Brand: IBASE Technology Pages: 76

Brand: Gigabyte Pages: 44

Spacewalker AV40

Brand: Shuttle Pages: 81

Gamefisher 298.586180

Brand: Gamefisher Pages: 23

Brand: Texas Instruments Pages: 21

Brand: Gigabyte Pages: 96

Brand: Gigabyte Pages: 96

Brand: DFI Pages: 92

Brand: IEI Technology Pages: 129

Brand: Dialog Pages: 12

Brand: Cytron Pages: 30

Brand: AMS Pages: 9

AS5601-SO_EK_ST

Brand: AMS Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands