10
Specifications
ULXD Specifications
Working Range
100 m (330 ft)
Note: Actual range depends on RF signal absorption, reflection and interference.
Audio Frequency Response
ULXD1
20 – 20 kHz (±1 dB)
ULXD2
Note: Dependent on microphone type
Audio Dynamic Range
System Gain @ +10
>120 dB, A-weighted, typical
System Audio Polarity
Positive pressure on microphone diaphragm produces positive voltage on pin 2 (with respect to pin
3 of XLR output) and the tip of the 6.35 mm (1/4-inch) output.
Operating Temperature Range
-18°C (0°F) to 50°C (122°F)
Note: Battery characteristics may limit this range.
Housing
ULXD4
ULXD1
ULXD2
steel
Cast aluminum
Machined aluminum
ULXD4Power Requirements
15 V DC @ 0.6 A, supplied by external power supply (tip positive)
Battery Type
Shure SB900 Rechargeable Li-Ion or LR6 AA batteries 1.5 V
Battery Life
SB900
alkaline
1/10 mW
20 mW
1/10 mW
20 mW
470 to 940
11 hours
7 hours
11 hours
5:30 hours
174 to 216
9:50 hours
7 hours
9 hours
5:45 hours
1240 to 1260
8:40 hours
6:45 hours
7:30 hours
5:30 hours
The values in this table are typical of fresh, high quality batteries. Battery runtime var-
ies depending on the manufacturer and age of the battery.
Frequency Range and Transmitter Output
Power
Band
Frequency Range
(
MHz
)
Power
(
mW RMS
)*
(Lo/Nm/Hi)
G50
470 to 534
1/10/20
G51
470 to 534
1/10/20
G52
479 to 534
1/10
H50
534 to 598
1/10/20
H51
534 to 598
1/10/20
H52
534 to 565
1/10
J50
572 to 636
1/10/20
J51
572 to 636
1/10/20
K51
606 to 670
1/10
L50
632 to 696
1/10/20
L51
632 to 696
1/10/20
L53
632 to 714
1/10/20
P51
710 to 782
1/10/20
R51
800 to 810
1/10/20
JB (Tx only)
806 to 810
1/10
AB (Rx and Tx)
770 to 810
'A' Band (770-805): 1/10/20
'B' Band (806-809): 1/10
Q51
794 to 806
1/10/20
V50
174 to 216
1/10/20
V51
174 to 216
1/10/20
X50
925 to 932
1/10
X51
925 to 937.5
10
X52
902 to 928
0.25/10/20
X53
902 to 907.500, 915
to 928
0.25/10/20
X54
915 to 928
0.25/10/20
Z16
1240 to 1260
1/10/20
* Power delivered to the antenna port
Note:
Frequency bands might not be available for sale or authorized for use in all
countries or regions.
Certifications
ULXD1, ULXD2, ULXD4
This product meets the Essential Requirements of all relevant European directives and
is eligible for CE marking.
ULXD1, ULXD2
Certified under FCC Part 74.
Certified by IC in Canada under RSS-102 and RSS-210.
IC:
616A-ULXD1 G50, 616A-ULXD1 H50, 616A-ULXD1 J50, 616A-ULXD1 L50;
616A-ULXD2 G50, 616A-ULXD2 H50, 616A-ULXD2 J50, 616A-ULXD2 L50.
FCC:
DD4ULXD1G50, DD4ULXD1H50, DD4ULXD1J50, DD4ULXD1L50;
DD4ULXD2G50, DD4ULXD2H50, DD4ULXD2J50, DD4ULXD2L50.
IC:
616A-ULXD1X52, 616A-ULXD2X52
FCC:
DD4ULXD1X52, DD4ULXD2X52
IC:
616A-ULXD1V50, 616A-ULXD2V50
FCC:
DD4ULXD1V50, DD4ULXD2V50
Note:
For transmitters operating in the V50 and V51 bands: nominal free space an-
tenna gain at middle of the band is typically -6 dBi, and rolls off at the band edges an
additional -4 dB.
ULXD4
Approved under the Declaration of Conformity (DoC) provision of FCC Part 15.
Conforms to electrical safety requirements based on IEC 60065.
The CE Declaration of Conformity can be obtained from: www.shure.com/europe/
compliance
Authorized European representative:
Shure Europe GmbH
Headquarters Europe, Middle East & Africa
Department: EMEA Approval
Jakob-Dieffenbacher-Str. 12
75031 Eppingen, Germany
Phone: 49-7262-92 49 0
Fax: 49-7262-92 49 11 4
Email: [email protected]
