background image

Shur-Co

®

, LLC Terms & Conditions

SHIPPING.

 Orders are shipped F.O.B. from the Shur-Co

®

, LLC sites listed be-

low. No full freight isallowed or prepaid shipment accepted unless quoted and 

approved in writing prior to acceptance of the order. All shipments are made 

by the most reasonable means in accordance with size and weight of order, 

unless specifi ed routing instructions are furnished by the customer. Shipments 

are made daily via U.P.S. and common carrier. Claims for shortages must 

be made within 10 days. All claims for damages or loss in transit must be 

made with the carrier. No collect calls will be accepted. To ensure delivery of 

orders, we need your full street address and phone number. When you receive 

your shipment, examine it carefully. Be sure all cartons listed on the delivery 

sheet are accounted for. Large items may be packaged separately. If a carton 

is damaged, open it and inspect the contents before signing for delivery. If 

merchandise is damaged, describe damage on the delivery receipt. Failure 

on your part to document damaged or missing merchandise on the delivery 

receipt releases the carrier of all liability; repair or replacement will be the 

customer’s responsibility.

 

WARRANTY.

 We warrant all new products are free of defects in materials and 

workmanship.* This warranty is effective if products are properly installed and 

used for the purpose for which they were intended and applies to the original 

buyer only. Except as set forth above or in any product-specifi c warranty docu-

mentation, we make no other warranties, express or implied, including but not 

limited to warranties of merchantability of fi tness for a particular use.

Returns of a product for warranty must be accompanied by a Return Merchan-

dise Authorization number (RMA#), obtained by by calling Customer Service 

at 866-748-7435, and sent, with freight paid by us, to Shur-Co

®

, LLC, 2309 

Shur-Lok St., PO Box 713, Yankton, SD 57078. All products returned without 

an RMA# will be refused. When we issue the RMA#, we will also issue a call 

tag to have UPS (or other freight company) pick up the product. C.O.D. returns 

not accepted. We will pay no storage fees for a warranty product return prior to 

pick by us or the freight company. If a warranty product return is scheduled to 

be picked up by us, we will pick up the product at our earliest convenience.

If a product returned is found, in our judgement, to be defective in material 

or workmanship, our obligation under this warranty is limited to the repair or 

replacement of the product, which will be made by us. Repair or replacement 

will be at our discretion, with replacements being made using current products 

performing in the equivalent function. Labor charges, other than those incurred 

at our factory, including, but not limited to, any labor to install a repaired or re-

placement product, are not covered under this warranty. All expenses associ-

ated with delivering defective products to our factory and delivering repaired or 

replacement products from our factory to the owner will be paid by us.
If the product returned is found, in our judgement, to be non-warrantable, the 

owner will be contacted to authorize repair work, purchase of a replacement 

product or return of the product, all of which will be at the owner’s expense. 

Payment authorization must be received by us before any non-warrantable 

product is repaired, replaced or returned. All expenses associated with deliver-

ing the repaired non-warrantable product, a replacement product or the non-

warrantable product from our factory to the owner will be paid by the owner.
In no event will we be liable for any damages of any kind to person, product or 

property, including but not limited to indirect, incidental, special, consequential 

or punitive damages, or damages for loss of profi ts or revenue, even if we 

have been advised of the possibility of such damages. There are no warran-

ties for used products or products that have been repaired, altered, modifi ed 

or subjected to misuse, negligence or accident. We will not repair or replace 

products that fail or malfunction due to ordinary wear and tear, except as ex-

pressly noted in a product-specifi c warranty. Use of non-Shur-Co

®

, LLC parts 

in conjuction with Shur-Co

®

, LLC products will void this product warranty.

*Certain products have specifi c warranties that differ from this warranty, for example motors and elec-

tronics. Product-specifi c warranty documentation is available for these items. In the event of a confl ict 

between this warranty and a product-specifi c warranty, the product-specifi c warranty will govern.

RETURN POLICY.

 All sales fi nal. See WARRANTY above for return details.

OTHER.

 All prices, product listings, sizes, weights and manufacturing details 

are subject to change without notice. No person is authorized to modify the 

foregoing conditions of sale whatsoever.

SHUR-CO

® 

of NORTH DAKOTA

1746 4th Ave. NW

West Fargo, ND 58078

Ph 877.868.4488 | Fax 701.277.1283

SHUR-CO

® 

 of OHIO

1100 N. Freedom, St. Rt. 88 & 14

Ravenna, OH 44266

Ph 866.356.0242 | Fax 330.297.5599

SHUR-CO

® 

 UK, Ltd.

Unit 41 Rochester Airport Estates

Laker Rd., Rochester, Kent ME1 3QX

Ph +44 (0)1795.473499

Fax +44 (0)871.272.8278

For more info, log on to our website:

www.shurco.com

Corporate HQ and Outlet Store

SHUR-CO

® 

 of SOUTH DAKOTA

2309 Shur-Lok St., PO Box 713

Yankton, SD 57078-0713

Ph 800.474.8756 | Fax 605.665.0501

     

ShurTite™ Service Centers

     

     SHUR-CO

® 

 of CANADA

     490 Elgin St., Unit #1

     Brantford, Ontario N3S 7P8

     Ph 800.265.0823 | Fax 519.751.3997 

     SHUR-CO

® 

 of SIOUX FALLS

     47184 258th St., Suite B

     Sioux Falls, SD 57107

     Ph 844.573.9322 | Fax 605.543.5469

     SHUR-CO

® 

 of ILLINOIS

     

Ph 866.356.0246 | Fax 217.877.8270

     SHUR-CO

® 

 of OHIO

     

Ph 866.356.0242 | Fax 330.297.5599

SHUR-CO

® 

 of FLORIDA

3353 SE Gran Park Way

Stuart, FL 34997

Ph 800.327.8287 | Fax 772.287.0431 

SHUR-CO

® 

 of ILLINOIS

3993 E. Mueller Ave.

Decatur, IL 62526

Ph 866.356.0246 | Fax 217.877.8270

SHUR-CO

® 

 of IOWA

3839 Midway Blvd.

Ft. Dodge, IA 50501

Ph 866.356.0245 | Fax 515.576.5578

SHUR-CO

® 

 of MICHIGAN

5100 Lakeshore Dr.

Lexington, MI 48450

Ph 800.327.8287 | Fax 772.287.0431

SHUR-CO

®

, LLC SERVICE AND DISTRIBUTION CENTERS

P/N 1121681 Rev. P

Summary of Contents for 4500 HD Series





































Reviews: