Shur-Co 4500 HD Series Owner'S Manual Download Page 27

Page: 27 / 36

P/N 1121681 Rev. P

Operation

press

close

tarp

press

open

tarp

NOTE:

Tarp systems will operate in

EXPRESS MODE

when

using buttons on trailer-mounted control box, if encoder

wires are connected. For SMART2™ systems, travel stops

must also be set, otherwise you must press and hold

buttons. When in

EXPRESS MODE

, press and release

buttons to open and close tarp (operation will continue

until complete after releasing button). When in

MANUAL

MODE

, press and hold buttons (operation will stop if button

is released). See remote instruction manual for detailed

instructions on remote operation.

WARNING

Stay clear of roll tarp and arm(s) area of travel during
operation. Failure to do so could result in serious
injury or death.

NOTE:

Tarp systems operate in

EXPRESS MODE

when

commanded to operate from buttons on trailer-mounted

control box. Closing remote lid or pressing select button will

not stop system in this case. Pressing

OPEN

CLOSE

button on remote will stop system if in range.

NOTE:

Tarp systems operate in

EXPRESS MODE

when

using buttons on trailer-mounted control box, if encoder

wires are connected. For SMART2™ systems, travel stops

must also be set. Otherwise you must press and hold

buttons (see remote instructions for SMART2™ systems).

NOTE:

4500 Series HD trailer-mounted control boxes now

operate in

EXPRESS MODE

. Pressing

button

on control box initiates express open or close operation.

After that, pressing either button will stop tarp operation. If

neither button is pressed, operation will automatically stop

at end of travel. On SMART2™ systems, if travel stops are

not set, trailer-mounted control box operates in

MANUAL

(momentary)

MODE

. Remotes for both systems are shipped

with tarp channel set to

EXPRESS MODE

and can be

configured as desired.

NOTICE

Decal shown above must be placed above wire-

less receiver on front of box.

Summary of Contents for 4500 HD Series





































Search results

Summary of Contents for 4500 HD Series

Reviews:

Related manuals for 4500 HD Series

Brands by name

Popular brands

Shur-Co 4500 HD Series, Owner'S Manual

Search results

Summary of Contents for 4500 HD Series

Reviews:

Related manuals for 4500 HD Series

Brands by name

Popular brands