background image

 

 

 

44 

 

  

 

 

Spectral M1500 Zoom Q4 MKIII 

Product code: 43549 

9.

 

Deinstallation, Transportation and Storage 

 

Instructions for Deinstallation 

 

WARNING 
Incorrect deinstallation can cause serious injuries and damage of property. 

 

Let the device cool down before dismounting. 

 

Disconnect power supply before deinstallation. 

 

Always observe the national and site-specific regulations during deinstallation and derigging of the 
device. 

 

Wear personal protective equipment in compliance with the national and site-specific regulations. 

 

Instructions for Transportation 

 

Use the original packaging to transport the device, if possible. 

 

Always observe the handling instructions printed on the outer carton box, for example: “Handle with 
care”, “This side up”, “Fragile”. 

 

Storage 

 

Clean the device before storing. Follow the cleaning instructions in chapter 8.1.1. Basic Cleaning 
Instructions
 on page 42. 

 

Store the device in the original packaging, if possible. 

10.

 

Disposal 

 

 

Correct disposal of this product 

Waste Electrical and Electronic Equipment 

This symbol on the product, its packaging or documents indicates that the product 
shall not be treated as household waste. Dispose of this product by handing it to the 
respective collection point for recycling of electrical and electronic equipment. This is 
to avoid environmental damage or personal injury due to uncontrolled waste 
disposal. For more detailed information about recycling of this product contact the 
local authorities or the authorized dealer. 

11.

 

Approval 

 

 

 

 

 
Check the respective product page on the website of Highlite International (

www.highlite.com

) for an 

available declaration of conformity. 
 

 

Summary of Contents for Spectral M1500 Zoom Q4 MKII

















































Reviews: