19
17. Internal program playback
You can control each fixture’s 5 built-in Programs, with 10 scenes each.
1)
Use the UP/DOWN buttons to scroll through the display, until it shows “
PGrun
”.
2)
Press the ENTER button and “
OFF
” will begin to flash on the display.
3)
Use the UP/DOWN buttons to select the desired program (1-5) or OFF. If OFF is set, the fixture will not
play
any of its built-in programs.
4)
Press ENTER to store your setting and exit the DMX Delay menu.
18. Programmer (Stand-alone Mode)
The Program menu allows you to individually carry out the City Painter’s on-board programming for any
stand-alone operation, without using external DMX control. You can also program a maximum of 29
SLAVE fixtures connected to the MASTER fixture, with the Program menu.
1)
Use the UP/DOWN buttons to scroll through the display, until it shows “
PGset
”.
2)
Press and hold down the ENTER button for six seconds.
3)
The display will show “
Prog.
” (1-5). Use the UP/DOWN buttons to change the value from 0-5.
Press the ENTER button to return to the previous menu.
4)
Use the UP Button to scroll through the menu until the display shows “
Scene
” (1-10). Use the UP/DOWN
buttons to change the value from 0-10. Press the ENTER button to store your setting and return to the
previous menu.
5)
Use the UP Button to scroll through the menu until the display shows “
Fixt.
”. Use the UP/DOWN buttons
to scroll through the display and select ALL, ODD, EVEN, mastR, slv01-slv029. Press the ENTER button to
store your setting and return to the previous menu.
6)
Use the UP Button to scroll through the menu until the display shows “
Shutt
” (0-255). Use the UP/DOWN
buttons to change the value from 0-255. Press the ENTER button to store your setting and return to the
previous menu.
7)
Use the UP Button to scroll through the menu until the display shows “
Dimmer
” (0-255). Use the
UP/DOWN buttons to change the value from 0-255. Press the ENTER button to store your setting and
return to the previous menu.
8)
Use the UP Button to scroll through the menu until the display shows “
R=255
” (0-255). Use the UP/DOWN
buttons to change the value from 0-255. Press the ENTER button to store your setting and return to the
previous menu.
9)
Use the UP Button to scroll through the menu until the display shows “
G=255
” (0-255). Use the UP/DOWN
buttons to change the value from 0-255. Press the ENTER button to store your setting and return to the
previous menu.
10)
Use the UP Button to scroll through the menu until the display shows “
B=255
” (0-255). Use the
UP/DOWN buttons to change the value from 0-255. Press the ENTER button to store your setting and
return to the previous menu.
11)
Use the UP Button to scroll through the menu until the display shows “
Mac
”. (0-255). Use the UP/DOWN
buttons to change the value from 0-255. Press the ENTER button to store your setting and return to the
previous menu.
12)
Use the UP Button to scroll through the menu until the display shows “
tm_H
”. (0-23). Use the UP/DOWN
buttons to change the value from 0-23. Press the ENTER button to store your setting and return to the
previous menu.
13)
Use the UP Button to scroll through the menu until the display shows “
tm_m
”. (0-59). Use the UP/DOWN
buttons to change the value from 0-59. Press the ENTER button to store your setting and return to the
previous menu.
14)
Use the UP Button to scroll through the menu until the display shows “
tm_s
”. (0-59). Use the UP/DOWN
buttons to change the value from 0-59. Press the ENTER button to store your setting and return to the
previous menu.
15)
Use the UP Button to scroll through the menu until the display shows “
Fd_H
”. (0-23). Use the UP/DOWN
buttons to change the value from 0-23. Press the ENTER button to store your setting and return to the
