SHOWTEC 50705 Manual Download Page 13

Page: 13 / 24

Order code: 50705

ColorCue 3

04)

Make sure the color selection mode is enabled. Turn the controls (E)–(J) to select the desired color.
The available colors are red, green, blue, white, amber and UV. Turning the control clockwise will
increase the color intensity. The display will show the color value in the range 0–255. If you want to
clear a selection, press the CLEAR button (44).

05)

If you want to select different colors for different fixtures, press the FIXTURES button(s) (13)–(24) once
again to cancel the selection of the fixture(s) you have made in step 2. The LED(s) on the button(s)
will turn off. Skip steps 5 and 6, if you have selected the same color for all connected fixtures.

06)

Repeat steps 2–5 to select colors for the remaining fixtures.

Crossfade between Bank A and Bank B (Double Control Mode)
01)

Create a scene in BANK A. Refer to Creating a Scene in Bank A on page 11.

02)

Slide the BANK A master fader (K) to 100 to output the scene and at the same time slide the BANK B
master fader (L) to 0.

03)

Create a scene in BANK B. Refer to Creating a Scene in Bank B on pages 11–12.

04)

Slide the BANK B master fader (L) to 100 to output the scene and at the same time slide the BANK A
master fader (K) to 0.

You can continue crossfading between Bank A and Bank B by sliding the master faders (K) and (L) up
and down, or you can repeat steps 1–4, each time creating a new scene in Bank A and Bank B.

Create a Scene (Single Control Mode)
Make sure the device is in single (24-fixture) control mode, see Control Modes on page 9–10 for more
information.
01)

Set the master fader (K) to 0, if you do not want to output the scene live while you are creating it. If
you set the master fader (K) to any other value, any changes you make will be output live.

02)

Press one or more FIXTURES buttons (01)–(24) to select the fixture(s) you want to control. The LED(s) on
the button(s) will light up. If you want to have the same color for all connected fixtures, press all
FIXTURES buttons (01)–(24). If you want to have different colors for each of the connected fixtures,
select only one fixture at this step. You can also select multiple fixtures, if you want to have one color
on more than one fixture. The selected fixtures will be highlighted on the display.

03)

Slide the FIXTURES faders (01)–(24) to adjust the light intensity of the connected fixtures selected in
step 2. The LEDs above the fixtures faders will light up.

04)

05)

If you want to select different colors for different fixtures, press the FIXTURES button(s) (01)–(24) once
again to cancel the selection of the fixture(s) you have made in step 2. The LED(s) on the button(s)
will turn off. Skip steps 5 and 6, if you have selected the same color for all connected fixtures.

06)

Repeat steps 2–5 to select colors for the remaining fixtures.

07)

Slide the BANK A master fader (K) to 100 to output the scene. Skip this step, if you have already set
the master fader (K) to 100.

Transition between Scenes (Single Control Mode)
01)

Create a scene following the instructions in Create a Scene on page 12.

02)

Press the HOLD button (41) to hold the output colors and intensities of the connected fixtures. The
LED on the button will light up. Now you can continue with changing the output colors and intensities
for the next scene without affecting the live output.

03)

Repeat steps 1 and 2 to create each time a new scene and to transition between the two scenes.

Note: Transitioning between scenes in single (24-fixtures) mode is without crossfading.