FILTER INSTALLATION AND MAINTENANCE (CONT’D)
WARNING
–
KEEP FILTERS CLEAN. EFFICIENCY OF THE VACUUM IS LARGELY
DEPENDENT ON THE FILTER. A CLOGGED FILTER CAN CAUSE OVERHEATING AND POSSIBLY
DAMAGE THE CLEANER. CHECK THE FILTER PERIODICALLY AND REPLACE AS REqUIRED.
WET PICK UP OPERATION
1. Your vacuum can be used for wet pick up. Remove ALL dirt and debris found in the tank. Remove all dry
use filters from the vacuum.
2. A clean cartridge filter may be used to pick up small quantities of liquid. To use the cartridge filter; follow
the instructions under dry pick up.
3. For vacuuming large quantities of liquid use a foam sleeve. If a foam sleeve did not come standard with
your unit, one may be purchased at your local dealer, the Shop-Vac
®
website or by contacting Shop-Vac
®
customer service. To use the foam sleeve; follow the instructions in this section.
4. Misting in the exhaust air or dripping of liquid around the tank cover may occur if the filter becomes
saturated during wet pick up. If this occurs, remove the filter and allow to dry, or replace with another dry
filter.
5. Turn the unit off immediately upon completing a wet pick up job or when tank is full and ready to be
emptied. When the tank is full, suction will drastically reduce. Refer to the automatic suction shut
off section for more information. Raise the hose to drain any excess liquid into the tank. Follow the
instructions in the emptying liquid waste section.
6. Before storing the vacuum cleaner or using for dry pick up, clean and dry the interior of the tank and the
underside of the tank cover. Clean and allow the filters to dry completely.
7. Wet pick up accessories should be washed periodically; especially after picking up wet, sticky kitchen
accidents. This can be accomplished with a warm solution of soap and water.
FOAM SLEEVE
1. With the tank cover in an upside down position, slide the foam sleeve down over the lid cage, pulling
until foam sleeve completely covers the lid cage.
2. Place the filter retainer onto the top of the foam sleeve. hold the tank cover with one
hand, turn the handle on the filter retainer clockwise to lock the filter into place.
3. To clean the foam sleeve, hold the tank cover and turn the filter retainer counter-
clockwise to loosen and remove. Slide the foam sleeve up and off the lidcage. Shake
excess debris off of the foam sleeve with a rapid up and down movement.
4. hold foam sleeve under running water for a couple minutes, rinsing from the inside of
the filter. A water wash is not always required, depending on the condition of the filter.
5. Check the filter for tears. If any are found, replace with a new filter.
EMPTYING LIqUID WASTE FROM THE TANK
NOTE:
Vacuum must be detached from toolbox before tank cover can be removed. Refer to Attach/Detach
Toolbox section in this manual.
To empty liquid waste from the tank, turn the vacuum off and remove the plug from the wall outlet. Remove
the tank cover and deposit the liquid waste in a suitable drain. After tank is empty, return the tank cover to
its original position.
AUTOMATIC SUCTION SHUT OFF
The vacuum is equipped with an automatic suction shut-off that operates when picking up liquids. As the
level of the liquid rises in the tank, an internal float rises until it seats itself against a seal at the intake of
the motor, shutting off suction. When this happens, the motor will develop a higher than normal pitch noise
and the suction is drastically reduced. If this occurs, turn unit off immediately. Failure to turn unit off after
float rises and shuts off suction will result in extensive damage to the motor. To continue use, empty the
liquid waste from the tank as outlined in the previous section.
NOTE:
IF ACCIDENTALLY TIPPED OVER, ThE VACUUM COULD LOSE SUCTION, IF ThIS OCCURS, TURN UNIT
OFF AND PLACE VAC IN UPRIGhT POSITION. ThIS WILL ALLOW ThE FLOAT TO RETURN TO ITS NORMAL
POSITION AND YOU WILL BE ABLE TO CONTINUE OPERATION.
LUBRICATION
No lubrication is necessary as the motor is equipped with lifetime lubricated bearings.
PAGE 8
