-24-
Df[\cN(/)0D]^%J`eZ\0&((
FG
<
I
8
K@FEJ
9\m\c:lkk`e^
The purpose of bevel cutting is to cut a specific angle into
the edge of a workpiece (see
=`^li\*+
).
The Model W1829 has preset fence stops at 45˚ inward,
90˚, and 45˚ outward (135˚). If your situation requires
a different angle, the preset fence stops can be easily
adjusted for your needs.
KfY\m\cZlkfek_\af`ek\i#[fk_\j\jk\gj1
(%
Read
and
understand
J8=<KP
, beginning on
GX^\-
.
)%
Make sure your stock has been inspected for danger-
ous conditions as described in the
JkfZb@ejg\Zk`fe
I\hl`i\d\ekj
instructions, on
GX^\)'
.
*%
Set the cutting depth for your operation.
Note:
N\jl^^\jkY\kn\\e
(
Ð
(-
Xe[
(
Ð
/
]fiY\m\c
Zlkk`e^#lj`e^Xdfi\j_Xccfn[\gk_]fi_Xi[nff[
jg\Z`\jfi]fin`[\jkfZb%
+%
Make sure your fence is set to the angle of your
desired cut.
,%
If your workpiece is cupped (warped), place it so the
concave side toward the fence.
-%
Start
the
jointer.
.%
With a push block in your leading hand, press
the workpiece against the table and fence with
firm pressure, and feed the workpiece over the
cutterhead, as in
Figure 35
.
Efk\
:
@]pflic\X[`e^_Xe[^\kjn`k_`e+f]k_\
Zlkk\i_\X[#c`]k`klgXe[fm\ik_\Zlkk\i_\X[#
Xe[gcXZ\k_\glj_YcfZbfek_\gfik`fef]k_\
nfibg`\Z\k_Xk`jfek_\flk]\\[kXYc\%Efn#]fZlj
pfligi\jjli\fek_\flk]\\[\e[f]k_\nfibg`\Z\
n_`c\]\\[`e^#Xe[i\g\Xkk_\jXd\XZk`fen`k_
pflikiX`c`e^_Xe[n_\e`k^\kjn`k_`e+f]k_\
Zlkk\i_\X[%Kfb\\gpfli_Xe[jjX]\#;FEFKc\k
k_\d^\kZcfj\ik_Xe+]ifdk_\Zlkk\i_\X[n_\e`k
`jdfm`e^
/%
Repeat
Jk\g.
until the angled cut is satisfactory to
your needs.
EFK@:<
@] pfl Xi\ efk \og\i`\eZ\[ n`k_ X
af`ek\i#j\kk_\[\gk_f]Zlkkf'#Xe[
giXZk`Z\ ]\\[`e^ k_\ nfibg`\Z\ XZifjj
k_\ kXYc\j Xj [\jZi`Y\[ Y\cfn% K_`j
gifZ\[li\ n`cc Y\kk\i gi\gXi\ pfl ]fi
k_\XZklXcfg\iXk`fe%
=`^li\*,%
Typical bevel cutting operation.
=`^li\*+%
Illustration of bevel cutting
results.
Portion
Removed With
Jointer
All manuals and user guides at all-guides.com
all-guides.com
