manualshive.com logo in svg

SHOEI Neotec II, Instructions For Use Manual, Page: 9 / 12

Share
Download
SHOEI Neotec II Instructions For Use Manual Download Page 9

17

16

Use the following procedures to remove or install 

the interior parts. Open the face cover completely 

when removing or installing the interior parts.

Removing Interior Parts

1. Removing the Cheek Pads

Draw the chinstrap from slit of noise isolator.

Then unfasten the 3 snaps to remove the pad

from the cheek pad base (Drawing 1), and pull 

the notch (a) from the cheek pad bracket (A) 

(Drawing 2). Next, pull the notch (b) from the

cheek pad bracket (B) as per Drawing 3. Do 

not pull it hard. Be sure to pull the front notch

(a) out first. If you pull out the rear notch (b) 

before pulling out notch (a), the plate may be 

damaged. 

2. Removing the Ear Pads

Unfasten the 4 clasps on the plate from the

cheek base, as shown in the drawing. Remove

the ear pad. Remove the other ear pad in the

same manner.

Removing and Installing Interior 

Parts

Center pad, right and left cheek pads, right and left 

chinstrap covers, and right and left ear pads can be 

removed for washing. You can also adjust the fit of 

your helmet by switching to the optional pads. Look 

at the list and drawing of interior parts and check 

whether the parts are installed or removed. Be 

sure to always fix the center pad, cheek pads, and 

chinstrap covers prior to riding. If necessary, use the 

following table to order the proper interior parts to 

adjust the fit of your helmet.

z

z

The same cheek pads can be used with all helmet 

sizes. For the M size helmet example, choose 

cheek pad size 31 if you want a looser fit and size 

39 for a firmer fit (both are optional parts).

z

z

Center pads varies by model size. Confirm the size 

of your helmet prior to making a purchase.

Replacing Interior Parts

3

2

1

a

b

4

Center Pad

Bonnet

Cheek Pad (R)

Coussinet maxillaire (D)

Cheek Pad (L)

Coussinet maxillaire (G)

Ear Pad (L)

Coussinet d’oreille (G)

Ear Pad (R)

Coussinet d’oreille (D)

Chinstrap Cover (R)

Couvre jugulaire (D)

Chinstrap Cover (L)

Couvre jugulaire (G)

Front

Rear

Noise Isolator

Hook

Cheek pad bracket (A)

Chinstrap

Slit/Fente

XS

S

M

L

XL

XXL

Center Pad

Optional (firm fit)

XS13

S13

M13

L13

XL13

XL9

Standard

XS9

S9

M9

L9

XL9

XL5

Optional (loose fit)

XS5

S5

M5

L5

XL5

N/A

Cheek Pad

Optional (firm fit)

39

39

39

39

39

35

Standard

35

35

35

35

35

31

Optional (loose fit)

31

31

31

31

31

N/A

Cheek pad bracket (B)

 

Summary of Contents for Neotec II













Reviews:

No comments