manualshive.com logo in svg

Shively Labs 6822, Instruction Manual Installation, Operation, & Maintenance, Page: 29 / 78

Share
Download
Shively Labs 6822 Instruction Manual Installation, Operation, & Maintenance Download Page 29

21

Connecting the Antenna (single-bay)

4

Connecting the Antenna (single-bay)

Connect the antenna 
bay.

The antenna bay is not pressurized. The feed system up to the bay may be 

pressurized. 
a. Provide a gas stop between the tower transmission line and the antenna 

input if necessary.

b. Connect the tower DIN transmission cable to the input of the antenna bay 

cable (

Figure 17

, 

8

). Tighten in accordance with 

Table 1

 on page 1. 

Figure 17. Single bay antenna 

connection

c. Loop or drape any excess cable and secure it to the pipe, using tie-wraps 

(

44

) or customer-supplied clamps, to prevent wind damage to the cables and 

to ensure the weight of the cable is not carried by the antenna input.

NOTE

The Model 6822 bay does not require pressurization or purging.

Installation of your Model 6822 single-bay is now complete. Please proceed to 

Startup

 on page 51.

Summary of Contents for 6822















































































Reviews:

No comments