Shining 3D FreeScan UE User Manual Download Page 10 | Manualshive

Page: 10 / 51

background image

FreeScan UE_ User Manual _V1.2.0.0 5

the windows system is. The software may work abnormally due to conflicts in authorizations.

Step 8 Click “

Finish

” t

o complete the installation.

Notes:

Check “Run FreeScan UE 1.2.X.X”, then click

on

“Finish”

. The software will run automatically after

installation is completed.

2.4 Upgrade

2.4.1 Upgrade Firmware

The basic working software of the Device is firmware. When the firmware version is too low and
incompatibility becomes an issue, it is necessary to upgrade the firmware, to get access to more updated
features.
Preparation before firmware upgrade:

⚫

Make sure that the device is powered on during the upgrade; avoid interrupted upgrade due to power

failure.

⚫

Back up the original firmware so as to retrieve it in case of upgrade failure or in case that the user finds

the new version unsatisfactory.

⚫

Download the new firmware files to the local computer where the software has been installed.

Upgrading process:

Each time when the software is run, the firmware status is automatically detected. If incompatible firmware is

detected, the system prompts the necessity for firmware upgrade, as shown in the figure below. Click

“Upgrade” to start the firmware upgrade.

«
...
8
9
10
11
12
...
»

Summary of Contents for FreeScan UE




















































Reviews:

No comments

Related manuals for FreeScan UE

Brand: DAVID Pages: 26

Brand: Easy Pix Pages: 2

Brand: Unitech Pages: 4

Brand: Unitech Pages: 2

Brand: Atlas Copco Pages: 44

Brand: Obdmate Pages: 36

Rosemount 5708 3D Solids Scanner DeltaV Series

Brand: Emerson Pages: 32

Brand: Emerson Pages: 204

Brand: Brother Pages: 36

Brand: Brother Pages: 159

Brand: Bell and Howell Pages: 108

Brand: Leidos Pages: 119

Brand: Plustek Pages: 31

Brand: Lomography Pages: 171

Pannoramic 1000

Brand: 3D Histech Pages: 79

Pannoramic SCAN 150

Brand: 3D Histech Pages: 132

Brand: Hasselblad Pages: 2

Brand: X-Rite Pages: 28

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands