manualshive.com logo in svg

Shimadzu BRANSIST safire HC9, Operation Manual

Share
Download
Shimadzu BRANSIST safire HC9 Operation Manual Download Page 47

47

6

Trouble 

Shooting

Other Messages

 

 The following message is displayed.   

Radiography is not possible while this message is displayed.

 

Action

 

Message 

Description

Door/Interlock

The examination room door 

is open.

Close the door.

FPD (Water) Flow Error

Heat Exchanger of FPD 

detects error.

Contact Shimadzu service 

representative.

(It's possible to perform 

fluoroscopy and 

radiography)

C-arm

 

■

 

Action

 

Message 

Description

Reset with the STOP 

switch or turn off and on 

the power again. If the 

equipment cannot be 

reset, contact Shimadzu 

service representative.

Motor Error XXX

Motor command fail to drive 

the motor.

Camera Rotation Error

Error of FPD rotation 

potentiometer.

Collimator Error XXX

Error of the collimator 

potentiometer.

Collimator Rot Error

Error of collimator rotation 

potentiometer.

Limit Error XXX

Detects the limit switch 

activation.

Ask Shimadzu service 

representative to readjust 

the limit switch.

It is possible to operate 

the C-arm by holding 

down the release switch. 

Reset with the STOP 

switch or turn off and on 

the power again. If the 

equipment cannot be 

reset, contact Shimadzu 

service representative.

Position Detect Error XXX

Mismatching of position 

detection and motor drive.

Potentio Error XXX

Detects disconnection of 

position detector circuit.

Summary of Contents for BRANSIST safire HC9



















































Reviews:

No comments

Brands by name

Popular brands

Load more brands