manualshive.com logo in svg

Shimadzu BRANSIST safire HC9, Operation Manual

Share
Download
Shimadzu BRANSIST safire HC9 Operation Manual Download Page 46

46

Messages Related to the X-ray Tube

 

 The following message is displayed.    

Radiography is not possible while this message is displayed.

 

Action

 

Message 

Description

Stop the operation until 

the heat unit value 

reduces.

Thermal Over

HU Over Predicted

HU Full Stored

Value predicted to go 

out of range Continuing 

radiography with present 

setting will cause heat unit 

overrun.

X-ray tube unit temperature 

exceeded the permitted limit.

Heat units reached the 

permitted limit.

(LX-Tube Water) Flow Error

Water flow in heat 

exchanger of X-ray tube is 

stopped.

Contact Shimadzu service 

representative.

(LX-Tube) Water Level Warning

Water volume of heat 

exchanger gets low 

representative.

Contact Shimadzu service 

representative. 

(It is possible to perform 

radiography though this 

warning message is 

displayed)

Error Messages at Power ON

 

Contact Shimadzu service 

representative.

Panel Battery Warning

The data recording battery in 

the operation panel must be 

replaced soon.

Cabinet Battery Empty

The data recording battery in 

the control cabinet is empty.

Cabinet Battery Warning

The data recording battery in 

the control cabinet must be 

replaced soon.

Panel Battery Empty

The data recording battery in 

the operation panel is empty.

Action

 

Message 

Description

Summary of Contents for BRANSIST safire HC9



















































Reviews:

No comments

Brands by name

Popular brands

Load more brands