Sherbourn PT-7030 User Manual Download Page 6

Page: 6 / 53

Page 1

PT-7030: User Manual

Contents

Important Safety Precautions and Explanation of Symbols
The Sherbourn PT-7030

.............................................................................2

About This Manual

......................................................................................2

Mechanical and Environmental

..................................................................3

Features .....................................................................................................4
Controls and Connectors ............................................................................5

Video Mode Support and Upsampling Options

........................................25

Configuration and Operation

....................................................................26

Input Configuration Paradigm

...................................................................26

Menus

.......................................................................................................27

Example Input Configuration

....................................................................41

Infrared (IR) and Serial (RS-232) Remote Control Codes

........................43

XLR Connector Pinouts

............................................................................44

Trigger Levels ...........................................................................................44

Periodic Maintenance

...............................................................................44

Sherbourn Technologies, LLC Ten-Year Limited Warranty

.......................45

Notes ........................................................................................................47

PT-7030

7.1 Channel AV Preamp / Processor

Summary of Contents for PT-7030






















































Search results

Summary of Contents for PT-7030

Reviews:

Related manuals for PT-7030

Brands by name

Popular brands

Sherbourn PT-7030, User Manual

Search results

Summary of Contents for PT-7030

Reviews:

Related manuals for PT-7030

Brands by name

Popular brands