background image

Page 12

Sherbourn Technologies, LLC Ten-Year Limited Warranty

What does this warranty cover?

  Sherbourn Technologies, LLC (“Sherbourn”) warrants its 

products against defects in materials and workmanship.  This warranty is subject to revision at any 

time.  

How long does this coverage last?

  This warranty commences on the date of retail purchase 

by the original retail purchaser and runs for a period of ten (10) years thereafter, with the following 

exceptions: (1) receivers (including the SR-8100, SR-8200, and SR-120), preamp/processors 

(including the PT-7030, PT-720C4, and PT-7020), preamplifiers (including the PRE-1), and the 

CD-1 CD Player (with the exception of the slot load CD engine) are covered by this warranty for 

five (5) years from the date of retail purchase by the original purchaser; and (2) electromechanical 

components, including the slot load CD engine on the CD-1 CD Player, and all fans (including 

the C-12 Cooling Unit), are covered by this warranty for three (3) years from the date of retail 

purchase by the original retail purchaser.  This warranty is transferrable, upon written notification 

to Sherbourn, to any person that owns the warranted product, however, if ownership is transferred, 

the Term shall be no longer than five (5) years from the date of purchase by the original purchaser.  

Sherbourn warrants any replacement product or part furnished hereunder against defects in 

materials and workmanship for the longer of the following: (i) the amount of time remaining under 

the original warranty, or (ii) 120 days from your receipt of the repaired or replaced product.  The 

duration described in the previous 3 sentences is hereinafter referred to as the “Term”.  TO THE 

FULLEST EXTENT PERMITTED BY LAW, ALL IMPLIED WARRANTIES RELATED TO THE 

ORIGINAL PRODUCT AND ANY REPLACEMENT PRODUCT OR PARTS (INCLUDING IMPLIED 

WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE) ARE 

EXPRESSLY LIMITED TO THE TERM OF THIS LIMITED WARRANTY.  SOME STATES DO 

NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE 

LIMITATION MAY NOT APPLY TO YOU.  A claim under this warranty must be made by you within 

the Term.  A claim shall not be valid (and Sherbourn has no obligation related to the claim) if it is not 

made within the Term and if it is not made in strict compliance with the requirements of the “How do 

you get service?” section.

What will Sherbourn do?

  Sherbourn will, at its option, either: (i) repair the product, or (ii) replace 

the product with a new consumer product which is identical or reasonably equivalent to the product.  

Sherbourn may provide you with a refund of the actual purchase price of the product in the event 

(i) Sherbourn is unable to provide replacement and repair is not commercially practicable or cannot 

be timely made, or (ii) you agree to accept a refund in lieu of other remedies hereunder.  When 

a product or part is repaired or replaced, any replacement item becomes your property and the 

replaced item becomes Sherbourn’s property. When a refund is given, the product for which the 

refund is provided must be returned to Sherbourn and becomes Sherbourn’s property.

What is not covered by this warranty?

  This warranty does not apply: (i) to damage caused by 

use with non-Sherbourn products, where the non-Sherbourn product is the cause of the damage; 

(ii) to damage caused by service or maintenance performed by anyone who is not a representative 

of Sherbourn; (iii) to damage caused by accident, abuse, misuse, flood, fire, earthquake or other 

external causes; (iv) to a product or part that has been modified after its retail purchase, where 

the modification caused or contributed to the damage; (v) to consumable parts, such as batteries; 

(vi) normal wear tear; or (vii) if any Sherbourn serial number has been removed or defaced and 

Sherbourn cannot otherwise confirm that you are the original retail purchaser or authorized 

transferee. SHERBOURN SHALL NOT BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL 

DAMAGES ARISING FROM OR RELATED TO ANY DEFECTS IN OR DAMAGES TO ITS 

Summary of Contents for PA 2-250




















Reviews: