Shearwell Data SDL400S User Manual Download Page 21

Page: 21 / 22

Printing

Print all groups

Print a group

To print all EID device numbers from within the

last group, make sure that you have a Bluetooth

printer on and ready with paper. Use the ‘Print

group’ option from the menu to print the EID device

numbers of all EIDs recorded in the current group.

The printout shows the following items:

Date

Time

Group

Animal count

EID Device read

The display mode will determine the EID format.

The printer will then disconnect.

To print all EID device from within all groups, make

sure that you have a Bluetooth printer on and

ready with paper. Use the ‘Print all groups’ option

from the menu.

The printout shows the following items:

Date

Time

Group

Animal count

EID Device read

No print out will be produced if Grp A=0

The display mode will determine the EID format.

The printer will then disconnect.

Print group?

Connecting...

Printing...

Disconnecting...

Print all groups?

Connecting...

Printing...

Disconnecting...

Summary of Contents for SDL400S























Search results

Summary of Contents for SDL400S

Reviews:

Related manuals for SDL400S

Brands by name

Popular brands

Shearwell Data SDL400S, User Manual

Search results

Summary of Contents for SDL400S

Reviews:

Related manuals for SDL400S

Brands by name

Popular brands