manualshive.com logo in svg

Shearwater NERD 2, Release Notes

Share
Download
Shearwater NERD 2 Release Notes Download Page 35

2021-07-21

Rev A

Page 35

Petrel 2 

only

Petrel 2 only

NOTE

After upgrading to v29, it is not possible to downgrade to earlier versions.

!

NEW

NEW

CHANGE

NEW

IMPROVE

CHANGE

Added a mini compass as an optional display on the center 
row.

The current compass numerical value (azimuth) is shown on 
the “Mark Heading” menu.

After marking a heading, if the new mini-compass is shown, 
returns to the main screen. If mini compass is not shown, re-
turns to the compass screen as before.

Timer (stopwatch) display added as an option on the configu-
rable center row or configurable bottom row.

More robust method of storing settings to better protect against transient conditions 
when a battery dies inside unit to prevent corruption of data.

Automatically turns on the unit when the absolute ambient pressure is greater than 
1100 mbar (previously was 1300 mbar). Result is faster auto-on when dive starts with 
Petrel turned-off. As a reminder, this auto-on feature is designed as a backup. We 
always recommend turning your Petrel on before a dive starts to confirm functionality 
and setup.

Petrel 2 

only

VERSION 29 

2015-06-26

Summary of Contents for NERD 2







































Reviews:

No comments

Brands by name

Popular brands

Load more brands