manualshive.com logo in svg

Shearwater NERD 2, Release Notes

Share
Download
Shearwater NERD 2 Release Notes Download Page 31

2021-07-21

Rev A

Page 31

IMPROVE

CHANGE

NEW

NEW

The ‘OC/CC’ mode has been renamed to ‘CC/BO’, where BO 
means bailout. 

Purpose is to clarify that OC/CC mode was never intended to 
be used for purely OC dives. Using the OC/CC mode for OC 
dives results in sub-optimal operation. This change clarifies 
the CC/BO mode is for closed circuit dives, with open circuit 
bailout. 

When diving OC, the mode should be set to either “OC Tec” or 
“OC Rec”.

A custom image can be used as the Perdix startup splash 
screen. The size image size must be 320x240 pixels. Shearwa-
ter Desktop version 2.5.4 or higher is required to upload imag-
es.

Better dive log page navigation. Allows moving backwards and forwards through the 
pages of dive logs (previously could only move forward or exit).

The gas will display in flashing red when its PPO2 is outside of 
a safe breathing range (i.e. below the min PPO2 or above the 
max PPO2 setting).

In CC mode, this warning refers to the diluent only. The 
breathing loop PPO2 may be in a safe range, but if the diluent 
is unsafe to breathe directly then the gas will be red. Note that 
other warnings exist to warn when the breathing loop is out-
side of a safe range.

“OC/CC” mode renamed 
to “CC/BO” for clarity of 

purpose

Add a custom startup image 

to the Perdix

Perdix 

only

The CC diluent is red to in-

dicate it is unsafe to breathe 

directly (PPO2 > 1.60)

VERSION 34 

2016-05-04

Summary of Contents for NERD 2







































Reviews:

No comments

Brands by name

Popular brands

Load more brands