manualshive.com logo in svg

Shearwater NERD 2, Release Notes

Share
Download
Shearwater NERD 2 Release Notes Download Page 27

2021-07-21

Rev A

Page 27

NOTE

A note on models:

 The NERD 2, Petrel, Petrel 2, Perdix, and Perdix AI share a com-

mon firmware base. Due to hardware differences, not all features are available on all 
models. The following changes apply to all models unless otherwise noted.

!

NOTE

Note on translations:

 Translated notes only cover the release notes from version 29 

to version 44. If you need information on more recent release notes you can refer 
to our English release notes. If you’re still having issues, please contact us at 

info@

shearwater.com

.

!

FIX

NEW

NEW

NERD 2 

only

NEW

CHANGE

IMPROVE

Added support for the NERD 2 hardware.

Added support for built-in li-ion charging and battery gauge.

Added “Stack Timer” feature for timing rebreather CO2 scrubber duration. This is a 
countdown timer, that can be optionally enabled in CCR modes. Has a user defined 
reset time, and is manually reset. Counts down when in dive mode, and generates 
alarms at 1 hour remaining time and 30 minutes remaining time.

Increased a Bluetooth timeout that was occasionally falsely triggering.

Allows user to access “End Dive” option whenever the absolute pressure is less than 
1.1 ATA. This is to allow breaking out of a dive that has falsely started (mostly likely 
due to having turned the unit on while in an airplane).

Improved calculations used in compass calibration.

NERD 2 

only

VERSION 46 

2017-09-01

Shearwater NERD 2 Release Notes

V46 is the first release for the NERD 2, and is only being released for 
the NERD 2.

Summary of Contents for NERD 2







































Reviews:

No comments

Brands by name

Popular brands

Load more brands