Shearwater NERD 2 Release Notes Download Page 3

Page: 3 / 38

Shearwater Petrel 2/Perdix/Perdix AI/NERD 2/

Peregrine Firmware v84 Release Notes

VERSION 84

2021-07-21

NEW

AI tanks can now be renamed. Only 2 characters
available per tank.

First character: T, S, B, O, or D

Second character: 1,2,3, or 4

DCIEM decompression model now available on some
dive computer models.

Only available for Air and Single Gas Nitrox open
circuit diving.

An additional fee is required to unlock this feature.
Contact your Authorised Shearwater Dealer for more
information.

(Perdix AI and

NERD 2)

(Open Circuit

Air and Nitrox

only)

NEW

A sidemount mode has been added.

The differences in sidemount mode are:

• Reminder indicators are shown to prompt

switching tanks.

• SAC and GTR are calculated on the pooled gas

quantity of the two tanks. The tanks must be the
same size.

• A RTR (Redundant Time Remaining) display

option has been added. This is the GTR calculated
only on the tank with less pressure (i.e. the GTR if
the higher pressure tank was lost).

(Perdix AI and

NERD 2)

2021-07-21

Rev A

Page 3

Summary of Contents for NERD 2







































Search results

Summary of Contents for NERD 2

Reviews:

Brands by name

Popular brands

Shearwater NERD 2, Release Notes

Search results

Summary of Contents for NERD 2

Reviews:

Brands by name

Popular brands