Sharp XV-Z21000 Operation Manual Download Page 51

Page: 51 / 68

-49

Appendix

Info

•

Be sure to remove the lamp unit by the han-

dle. Be sure not to touch the glass surface of
the lamp unit or the inside of the projector.

•

To avoid injury to yourself and damage to the

lamp, be sure to carefully follow the steps
below.

•

Do not loosen other screws than for the lamp

unit cover and lamp unit.

(As for the lamp unit, only the silver screws

are loosened.)

Press STANDBY on the pro-

jector or STANDBY on the re-

mote control to put the projector

into the standby mode.

•

Wait until the cooling fan stops.

Disconnect the power cord.

•

Unplug the power cord from the AC

socket.

•

Leave the lamp until it has fully cooled

down (about 1 hour).

Remove the lamp unit cover.

•

Loosen the user service screws that

secure the lamp unit cover. Then open
the cover in the direction of the arrow.

Remove the lamp unit.

•

Loosen the securing screws from the

lamp unit. Hold the lamp unit by the
handle and pull it in the direction of the
arrow.

Removing and Installing the Lamp Unit

Warning!

•

The lamp unit becomes very hot while the projector is operating. Do not remove the lamp

unit from the projector right after use. The lamp and parts around the lamp will be very hot
and may cause burns or injury.

Lamp unit
(Type: AN-K20LP)

Optional
accessory

STANDBY button

STANDBY

User service screws

Lamp unit

Lamp unit cover

Securing screw

Securing screws

Handle

AC socket

XVZ21000̲E̲Ousyu̲P46-51.indd 49

2006/07/31 19:55:54

Summary of Contents for XV-Z21000





































































Search results

Summary of Contents for XV-Z21000

Reviews:

Related manuals for XV-Z21000

Brands by name

Popular brands

Sharp XV-Z21000, Operation Manual

Search results

Summary of Contents for XV-Z21000

Reviews:

Related manuals for XV-Z21000

Brands by name

Popular brands