background image

To scan barcodes, connect the included barcode scanner to the cash register.

1.

Open the Serial/Scanner port cover at the right side of the register.

2.

Insert the connector of the barcode scanner into the Serial/Scanner
port, and tighten both of screws on the connector.

Always unplug the power cord of the cash register when
you connect or disconnect the barcode scanner.

8

GETTING STARTED

Please follow the procedure shown below.

Initializing the cash register

In order for the cash register to operate properly, you must initialize it before operating for the first time.

Follow this procedure.

1.

Make sure the power cord plug is 

not

inserted into the AC outlet.

2.

Insert the manager (MA) key into the mode switch and turn it to the PGM position.

3.

While holding down both the 

}

key and the 

l

key, insert the plug into the

AC outlet.  The buzzer will sound three times and “

???

MRS. 

???

” will

be displayed.

4.

The cash register has now been initialized.  The register display will now
show “0.00” with “PGM”.

If the buzzer does not sound when the plug is inserted, the initialization has not been done
successfully.  (This will occur when the voltage is high because you operated the cash register
before starting initialization.)  Wait at least ten seconds after pulling out the plug and initialize the
cash register again.

Find a stable surface near an AC outlet where the cash register will not subject to water sources or

direct sunlight .
Unpack the cash register and make sure all accessories are included.  For details of accessories, please refer to

Specifications

” section.

REG

OPX/Z

MGR

PGM

X1/Z1

X2/Z2

OFF

VOID

3

Installing the cash register

1

Connecting the barcode scanner

2

PGM
0.00

*** MRS. ***

Summary of Contents for XE-A402





























































































































Reviews: