Sharp SF-2540 Operation Manual Download Page 94 | Manualshive

Page: 94 / 104

background image

92

KEY OPERATOR PROGRAMS

Key operator programs

P45 Message Time Setting

Program P45 is used to adjust the length of time that messages are
displayed in the range of 1 to 12 seconds in 1 second increments.
When P45 is entered, the following message will appear.

P45: MESSAGE TIME SETTING.

SET THE TIME FOR MESSAGES ––

(1 TO 12 SECONDS). PRESS THE START

KEY AFTER ENTRY.

Set the time using the 10-key pad and press the START
key.

P46 Require Key Operator Code

Program P46 is used to prevent the copier from being started by
people other than the key operator. If this program is set, the
message “

ENTER KEY OPERATOR CODE.

” will appear each time

the power switch is turned to the “ON” position.
When P46 is entered, the following message will appear.

P46: REQUIRE KEY OPERATOR CODE.

1.YES 2.NO

To require key operator code entry for access to the
copier, press key 1.
To enable access to the copier without key operator code
entry, press key 2.

P47 Stream Feeding Mode

Program P47 is used to enable the stream feeding mode of an
optional document feeder. When the stream feeding mode is
enabled, additional originals which are set in the document feeder
tray within 5 seconds after the previous original was fed will be fed
and copied automatically.
When P47 is entered, the following message will appear.

P47: STREAM FEEDING MODE (DOCUMENT

FEEDER).

1.YES 2.NO

To enable the stream feeding mode, press key 1.
To disable the stream feeding mode, press key 2.

«
...
92
93
94
95
96
...
»

Summary of Contents for SF-2540









































































































Reviews:

No comments

Related manuals for SF-2540

Brand: Triumph Adler Pages: 311

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands