Sharp SF-2540 Operation Manual Download Page 87

Page: 87 / 104

KEY OPERATOR PROGRAMS

Key operator programs

To display all registered account numbers

Press key 4.

●

The following message will appear.

ACCOUNT NUMBER DISPLAY (PAGE 1)

TO SEE PAGE 2: PRESS THE KEY.

If you want to see the next display, press the SCROLL
DISPLAY key. Press the PROGRAM key to exit the
program.

P16 Account Limit Setting

Program P16 is used to set the maximum number of copies which
can be made against a registered account number.
When P16 is entered, the following message will appear.

P16: ACCOUNT LIMIT SETTING.

1.SET LIMIT 2.CANCEL LIMIT

To set a limit

Press key 1.

●

The following message will appear.

INPUT ACCOUNT NUMBER TO BE LIMITED

AND PRESS THE START KEY. –––––

Enter the account number to be limited.

●

To set a limit for all accounts, skip the account number entry
and proceed to the next step.

Press the START key.

●

The following message will appear.

INPUT MAXIMUM NUMBER OF COPIES FOR

ACCOUNT AND PRESS THE START KEY.

ACCOUNT NUMBER MAXIMUM

000,000

Enter the upper limit (max. 999,999) for the account.

Press the START key.

To limit other accounts, repeat steps 2 to 5. Press the
PROGRAM key to exit the program.

Summary of Contents for SF-2540









































































































Search results

Summary of Contents for SF-2540

Reviews:

Related manuals for SF-2540

Brands by name

Popular brands

Sharp SF-2540, Operation Manual

Search results

Summary of Contents for SF-2540

Reviews:

Related manuals for SF-2540

Brands by name

Popular brands