Sharp SF-2540 Operation Manual Download Page 66

Page: 66 / 104

OPTIONAL

EQUIPMENT

20-BIN STAPLE SORTER (SF-S56)

Open the stapler cover.

Lift the release lever and pull out the staple box.

●

Lift the release lever to unlock the staple box. Then pull out
the box.

Remove the empty staple cartridge from inside the
staple box.

Insert the new staple cartridge into the box until it
clicks in place.

●

Insert the new cartridge by aligning the arrows on the
cartridge with those on the box. Check that the cartridge locks
in place by pulling it slightly.

●

The cartridge holds 5,000 staples.

NOTE:
Be sure not to remove the rear paper and tape before inserting
the cartridge.

20-bin staple sorter (SF-S56)

Staple cartridge replacement

When the staple cartridge becomes empty, the message “

ADD

STAPLES. FOLLOW INSTRUCTIONS INSIDE THE SORTER.

” will

appear. Replace the staple cartridge as follows:

Summary of Contents for SF-2540









































































































Search results

Summary of Contents for SF-2540

Reviews:

Related manuals for SF-2540

Brands by name

Popular brands

Sharp SF-2540, Operation Manual

Search results

Summary of Contents for SF-2540

Reviews:

Related manuals for SF-2540

Brands by name

Popular brands