Sharp MX-M350, Service Manual, Page: 194 / 276

MX-M350/M450 N/U SIMULATION 9 - 55
6) Enter the above values as the set values of L1 and L2. (Enter
the adjustment values of L1 and L2, and press [P] key.)
If the adjustment result is not satisfactory, perform the above pro-
cedures again from the beginning, or use SIM 50-1 to adjust.
NOTE: If a satisfactory result is not obtained with the above proce-
dures, through the adjustment values are changed individ-
ually, the normal adjustment cannot be made.
Perform procedures 3) to 6) continuously.
(Rear edge void area adjustment)
Adjust so that the rear edge void area is 3.5mm. (Change the
adjustment value of TRAIL EDGE, and press [START] key.)
(Front/rear frame direction image loss adjustment)
Set the adjustment value of SIDE to 20. (Enter 20 as the adjust-
ment value of SIDE, and press [P] key.)
When this adjustment value is changed, the image position is
shifted in the front/rear frame direction.
(Front/rear frame direction void area adjustment)
Adjust so that the total of the front/rear direction void areas is
7.0mm. (Change the adjustment values of FRONT/REAR, and
press [START] key.)
Front frame void area = 3.5mm Rear frame void area = 3.5mm
If, as shown above, the front and the rear void areas are not even,
use SIM 50-5 to adjust the image off-center position.
NOTE: When [P] is pressed after entering an adjustment value,
the adjustment value is set. When [START] key is pressed
instead, the adjustment value is set and copying is per-
formed.)
(Copy condition in this simulation)
∗
To select paper (paper feed tray), perform the following proce-
dures.
1) Enter 0 with 10-key.
2) Press [START] key. (The mode is changed to the paper feed
tray selection mode.)
3) Enter the number corresponding to the paper feed tray of the
target paper with 10-key.
4) Press [START] key. (The paper feed tray is selected.)
∗
To set the magnification ratio, perform the following procedure.
1) Enter 2 with 10-key.
2) Press [START] key.
3) Enter the copy magnification ratio with 10-key.
4) Press [START] key.
Item Content
Set
range
Default
0 TRAY SELECT Paper feed tray
selection 1 - 5 –
1 COPY START Copy START
(Default) – –
2 MAGNIFICATION Print magnification
ratio 25 -
400%
400
(Lead edge adjustment value)
3
L1 Distance from the
image lead edge to
the scale of 10mm.
(Platen 400%,
0.1mm increment) 0 - 999 –
4 L2 Distance from the
paper lead edge to
the image lead edge
(0.1mm increment) –
(Image loss set value)
5 LEAD Lead edge image
loss set value 0 - 99 15
6 SIDE Side image loss set
value 20
(Void set value)
7
LEAD_EDGE
(DENA) Lead edge void set
value 0 - 99 35
8 TRAIL_EDGE
(DENB) Rear edge void
adjustment value
9 FRONT/REAR Front/Rear void
adjustment value 32
Normal display NOW COPYING.
ERROR display Door open DOOR OPEN.
Jam JAM
Paper empty PAPER EMPTY.
1 TRAY1 TRAY1
2 TRAY2 TRAY2
3 TRAY3 TRAY3
4 TRAY4 TRAY4
5 BPT Manual feed
Set range 25 - 400 (%)
Select 2, and
press [START] key. Press [START] key, or
press [SYSTEM SETTINGS] key.
320
1
2
SIMULATION 50-2
LEAD EDGE ADJUSTMENT(CALC). SELECT 0-9, AND PRESS
START.
0. TRAY SELECT
1 1.COPY START
2. MAGNIFICATION 400
(ADJUSTMENT) 3.L1 320 4.L2 105
(IMAEG LOSS SETTING) 5.LEAD 15 6.SIDE 20
(VOID SETTING) 7.LEAD_EDGE(DENA) 35
8.TRAIL_EDGE(DENB) 35 9.FRONT/REAR 32
Select other than 0 - 2, and press [START] key.
Press [SYSTEM SETTINGS] key.
Press [START] key.
Press [SYSTEM SETTINGS] key,
or terminate copying.
Press [START] key, or
press [SYSTEM SETTINGS] key.
SIMULATION 50-2
LEAD EDGE ADJUSTMENT(CALC). INPUT VALUE 0-99, AND PRESS
START.
3.L1
SIMULATION 50-2
LEAD EDGE ADJUSTMENT(CALC). NOW COPYING.
SIMULATION 50-2
LEAD EDGE ADJUSTMENT(CALC). SELECT 1-5, AND PRESS
START.
(FEED TRAY)
1.TRAY1 2.TRAY2 3.TRAY3 4.TRAY4
5.BPT
Select 1,
and press
[START] key.
Select 0, and press [START] key.
100
SIMULATION 50-2
LEAD EDGE ADJUSTMENT(CALC).
(MAGNIFICATION)
INPUT 25-400(%)