MX-3610N ADJUSTMENTS AND SETTINGS 4 – 72
6) Check the color balance and density.
(Refer to the item of the printer color balance and density
check.)
If the color balance is customized, use SIM 67-27 to register
the color balance as the service target.
If the color balance is not customized, this procedure is not
required.
If the customized color balance is registered as the service tar-
get, the automatic color balance adjustment can be made in
the next color balance adjustment.
10-F
Printer image quality adjustment
(Individual adjustment)
a. General
This adjustment is used to execute the fine adjustment in each
mode only when a satisfactory image quality is not obtained by the
basic adjustments ADJ 10E (1) and ADJ 10E (2) or there is a
request from the user. Normally there is no need to execute this
adjustment.
This must be well understood for execution of the adjustment.
10-F
(1)
Printer density adjustment
(Low density section density adjustment)
(No need to adjust normally)
This adjustment is used to adjust the image density in the low den-
sity area in the printer mode.
Adjust to reproduction setting of the low density image.
This adjustment is required in the following cases.
* When it is required not to reproduce images in the low density
section, or to reproduce low-density images.
* When there is request from the user.
1) Enter the SIM 67-36 mode.
2)
Enter the adjustment value and press the [OK] key.
In case of increase of the image density on low density part,
increase the adjustment value. For diluting the image density
on low density part, decrease the adjustment value.
10-F
(2)
Printer high density image density
reproduction setting (Supporting the high
density section tone gap)
(No need to adjust normally)
When a tone gap is generated in the high density section in the
printer mode, the setting is changed to lower the density in the high
density section.
This setting is normally not required, however, in the following
cases, a change of setting must be made.
* When a tone gap occurs on part of high density.
* To lower the density in the high density section.
a. Adjustment procedure
1)
Enter the SIM 67-34 mode.
2)
Select the item A, B with the scroll key.
OK
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
7(67
35,17(5+,*+/,*+7$'-8670(17
$˖
˷̚˹
˖$3$7&+,1387
$˖
2.
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
7(67
35,17(5+,*+/,*+7$'-8670(17
$˖
˷̚˹
˖$3$7&+,1387
$˖
2.
10-key
Display/Item
Content
Setting
range
Default
A
CMY
(0: ENABLE
1:DISABLE)
0
CMY engine maximum
density correction mode
Enable
0 - 1
0
1
CMY engine maximum
density correction mode
Disable
B
K
(0:ENABLE
1: DISABLE)
0
K engine maximum
density correction mode
Enable
0 - 1
1
1
K engine maximum
density correction mode
Disable
C
CYAN MAX
TARGET
Scanner target value for
CYAN maximum density
correction
0 - 999
500
OK
10-key
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
7(67
(1*,1(0$;,080'(16,7<$'-8670(1702'()2535,17(5
$˖
˷̚˹
˖&0<(1$%/(',6$%/(
$˖
˖.(1$%/(',6$%/(
%˖
˖&<$10$;7$5*(7
&˖
˖0$*(17$0$;7$5*(7
'˖
˖%/$&.0$;7$5*(7
)˖
˖<(//2:0$;7$5*(7
(˖
2.
ǂǂǂ6,08/$7,21ǂǂ12
&/26(
7(67
(1*,1(0$;,080'(16,7<$'-8670(1702'()2535,17(5
$˖
˷̚˹
˖&0<(1$%/(',6$%/(
$˖
˖.(1$%/(',6$%/(
%˖
˖&<$10$;7$5*(7
&˖
˖0$*(17$0$;7$5*(7
'˖
˖%/$&.0$;7$5*(7
)˖
˖<(//2:0$;7$5*(7
(˖
2.