manualshive.com logo in svg

Sharp LS013B7DH07, Technical Literature

Share
Download
Sharp LS013B7DH07 Technical Literature Download Page 9

 

 

SPEC    No. 

LD-28204A 

MODEL    No. 

LS013B7DH07 

PAGE 

7 

 

  [Precautions for Storage]

 

(1) After opening the package, do not leave the LCD panel in direct sun or under strong ultraviolet ray.     

Store in the dark place. 

(2)  In  temperature  lower  than  specified  rating,  liquid  crystal  material  will  coagulate.    In  temperature  higher 

than  specified  rating,  it  will  liquefies.    In  either  condition,  the  liquid  crystal  may  not  recover  its  original 

condition. Store the LCD panel in at or around room temperature as much as possible.   

Also, storing the LCD panel in high humidity will damage the polarizer.     

Store in normal room temperature as much as possible. 

(3) Keeping Method 

      a. Don't keeping under the direct sunlight.                  b. Keeping in the tray under the dark place. 

 

 

 

 

 

SHARP Confidential 

technical 

literature

 ©Copyright 2016 SHARP All rights reserved

 ©Copyright 2016 SHARP All rights reserved

Summary of Contents for LS013B7DH07



































Reviews:

No comments

Brands by name

Popular brands

Load more brands